Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
5. Install rod (7) through holes in bottom pole section (3) and 25. Install handle assembly to lower elevator tubes (35) using eyebolt (8). bolt (36), spacers (37) and nut (38). NOTE: Before going onto the 6. Insert pole assembly into tank assembly as shown. Secure pole next step, set adjustment system to the 10’ (3.05m) setting. assembly with upper pivot bracket (9) and lock nut (10). 26. Insert bolt (36) through the left side upper elevator tube (40), then IMPORTANT! Two people recommended for this step. stretch spring (42) onto bolt (36). Insert bolt (36) through the right 7. Secure base struts (11) to pole using bolt (12) washers (13) and nut side upper elevator tube (40) and secure with nut (38). (15) as shown. WARNING: USE EYE PROTECTION WHEN INSTALLING WARNING: TIGHTEN BOLT (12) IN LOCK NUT (15) UNTIL SPRINGS. FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. 27. Roll completed assembly to desired playing area. Secure assembly Rotate the non-secured ends of base struts (11) as shown. to ground using T-Strap (45) and tie down stake (46). Fill tank with 8. Secure base struts (11) to base using bolt (16) washers (13) 34 gallons of water. IMPORTANT! Add two gallons (7.6 Liters) of and nut (14). non-toxic antifreeze in sub-freezing climates. 9. Insert carriage bolts (18) into middle set of holes on wheel bracket WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN (21) as shown. Attach lower pivot bracket (17) to wheel bracket EMPTY, MAY TIP OVER. using bolt (18), washers (13), disc (28), and nut (10) as shown. 28. While holding handle, remove pin (60). Tighten completely. 29. Move elevator up or down to desired height. 10. Attach handle bar (20) to wheel bracket assembly using nuts (14) as 30. Replace pin full length to lock system at desired height. shown. WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. 11. Install wheels (3) onto axle (24) and wheel bracket assembly with 31. Apply height and moving label (47) to front of pole as shown. push caps (25) as shown. 12. Attach wheel bracket assembly to base assembly using bolt (19), WARNING: USE OF THIS PRODUCT WITHOUT PROPER washers (13), and nut (10) as shown. INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART 13. Carefully reposition entire assembly as shown. CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. 14. Attach front of plastic handle (26) to back of plastic handle (23) BE SURE TO FOLLOW DIRECTIONS CAREFULLY. around handle bar (20) using self- tapping screws (27) as shown. IMPORTANT! Front of plastic handle (26) should face outward, 32. Install net clips as shown. (See illustration) away from pole assembly. 15. Insert bolts (66) through plastic handle assembly, handle bar (20), 33. Install net as shown. (See illustration) and attach nuts (14) as shown. Tighten completely. IMPORTANT! Two people recommended for this step. 16. Install pole mount bracket (53) with carriage bolts (54) as shown. Tighten flange nuts (14) completely. 17. Attach spacers (55, 56) to pole mount bracket (53) with bolts (33), washers (57), and nuts (34) as shown. IMPORTANT! Tighten until washers (57) no longer move. 18. Attach covers (58) onto pole mount bracket (53) with carriage bolt (39) and nut (14) as shown. IMPORTANT! Loop end of pin lanyard (59) over carriage bolt (39) during this assembly. P/N 214949A 01/03 4 PARTS LIST See Hardware Identifier Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Qty. 1 1 1 1 4 1 1 1 1 3 2 1 10* 13* 1 2 1 2 1 1 1 4 1 1 2 1 4 1 2 2 4* 4 4* 5 Part No. 904847 978482 900284 206615 226401 200628 202820 206934 206949 203063 906410 202541 203218 203100 203220 203798 206948 206252 203330 906606 900223 203103 206604 206940 206938 206605 204804 206956 900964 200874 205528 201642 206360 201124 Description Top Pole Section (Black) Middle Pole Section (Black) Bottom Pole Section (Black) Base Wheel Wheel Axle, 11-3/4 Long Rod, 3/8 x 4-3/4 Long Eyebolt Pivot Bracket, Upper Lock Nut, 3/8-16 Nylon Insert Base Strut (Black) Bolt, Hex Head 5/16-18 x 3-3/4 Long Washer, Flat, 3/8 I.D. Nut, Hex Flange 5/16-18 Lock Nut, 5/16-18 , Nylon Insert Bolt, Hex Flange, 5/16-18 x 1-1/2 Long Pivot Bracket, Lower Bolt, Hex Head, 3/8-16 x 1 Long Bolt, Hex Head, 3/8-16 x 4-1/2 Long Handle Bar Wheel Bracket Carriage Bolt, 5/16-18 x 2 Long Handle, Back Plastic Axle Push Cap Handle, Front Plastic Screw, Phillips Head, 3/4” Long Disc, 5” O.D. x 13/32 I.D., Plastic Bracket, Elevator Mount Spacer, Steel .402 I.D.x.50 O.D.x1.5 Long Bolt, Hex Flange, 5/16-18 x 1 Long Spacer .530 I.D. x.63 O.D. x .63 Long Bolt, Hex Head, 3/8-16 x 2-5/8 Long Lock Nut, Hex Head, 3/8-16 Item Qty. Part No. Description 35 2 904821 Elevator Tubes, Lower - Long 36 6 206304 Bolt, Hex Head, 1/2-13 x 6-5/16 Long 37 4 206311 Spacer, Plastic, .530 I.D. x .50 Long 38 6 206340 Lock Nut, Hex Head, 1/2-13 39 1 203038 Carriage Bolt, 5/16-18 x 2-3/4 Long 40 2 904808 Elevator Tube, Upper -Short 41 1 202814 Cap, Pole Top 42 1 204837 Spring 43 12 201219 Smart Clip, Net Holder 44 2 203617 Cap...