Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
NOTE: Install H-Frame (13) with foam striping toward backboard. Do this strip last. 11. 16 4 13 9 4 7 4 10 7 4 10 7 4 16 4 7 4 9 16 4 16 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPORTANT! Do not over tighten. 14 14 14 1514 13 14 Cut foam stripping (14) to sizes shown and attach to flat side of H-frame (13) as shown. Then secure H-frame to support arms (9 & 10). NOTE: Install H-Frame (13) with foam striping toward backboard. Do this strip last. 7 01/03 P/N 211560H Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rotating. Rotate handle clockwise on crank jack to the fully extended position. Upright crank jack. 12. Secure jack brackets (17 & 18) to lower holes in pole as shown. 13. IMPORTANT! HOLD HERE 20 7 4 17 4 18 19 19 4 4 7 12. Secure jack brackets (17 & 18) to lower holes in pole as shown. 13. IMPORTANT! HOLD HERE 20 7 4 17 4 18 19 19 4 4 7 P/N 211560H 01/03 8 46 14. Install crank jack (20) U-joint to lower set of support arms (10) as shown. 10 4 20 7 4 12 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPORTANT! Do not over tighten. 46 14. Install crank jack (20) U-joint to lower set of support arms (10) as shown. 10 4 20 7 4 12 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPORTANT! Do not over tighten. REAR VIEW 9 01/03 P/N 211560H 15. 19 17 20 4 21 21 7 4 18 15. 19 17 20 4 21 21 7 4 18 WARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. Rotate jack handle clockwise to raise H-frame (13) to approximately 7’ (2.1 m) from ground. Secure crank jack (20) to jack brackets (17 &18) as shown. NOTE: Some adjustment will be necessary to align the lower crank jack bushing to jack brackets (17 & 18). REAR VIEW P/N 211560H 01/03 10 16. 16. While H-frame (13) is in the lowest position, hang backboard onto H-frame (13). NOTE: Backboard frame will rest on top of H-frame. Secure backboard with hardware as shown. *ONLY Fingertighten bolts (22) with nuts (23). Repeat procedure for opposite side. 23 22 13 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING 11 01/03 P/N 211560H RIM ASSEMBLY & INSTALLATION WARNING 17. Install carriage bolt (41) through rim (25), washers (4) and (27) as shown. Tighten nut (43) completely. Place nut (42) about half-way up carriage bolt (41) as shown. 25 4 41 27 43 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. 42 41 27 Attach bracket (39) to backboard and support structure by inserting bolts (26) and washers (24) through top holes in bracket (39), Tighten nuts (23) completely. 26 39 24 23 2418. 23 24 24 40 26 Insert inner bracket (40) into bracket (39) as shown. Insert bolts (26) and washers (24) through top holes of inner bracket (40) as shown, *FROM STEP 13- Now tighten backboard/frame nuts (23) completely. 19. 39 40 39 P/N 211560H 01/03 12 20. 20. Insert spacer (45) through rim assembly (25). Place rim assembly on bracket (39) so that carriage bolt (41) is inserted through hole on top of inner bracket (40). Install hex bolt (44), washers (27) and nut (42) through top holes on bracket (39) through spacer (45) as shown.Tighten completely. 2539 40 BOTTOM VIEW 45 25 41 27 44 2727 45 42 21. Install rubber grommet (28), concave washer (29) and center lock nut (30) to carriage bolt (41) as shown. NOTE Do not over tighten as rim will not flex properly. See leveling instructions to determine how much to tighten nuts (42) and (30). 28 41 30 29 13 01/03 P/N 211560H 22. LEVELING INSTRUCTIONS: Place level on rim (25) and adjust nut (42) until level. Tighten nut (30) to set rim tension for playing. LEVELING...
Otros modelos de este manual:Formadores - AC4062 (879.51 kb)
Formadores - AC4064 (879.51 kb)
Formadores - AC4054 (879.51 kb)