Votos - 2, Puntuación media: 4 ( )

Fabricar: Huffy Tamaño del archivo: 879.51 kb Nombre del archivo: Idioma del manual:

4 38 3 7 6 Note: Offset holes go to back of system. 4 5 1 Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2) from Step 2. Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING PLAYING SURFACE PLAYING SURFACE IMPORTANT! Holes in pole must be parallel with playing surface. 4 38 3 7 6 Note: Offset holes go to back of system. 4 5 1 5 01/03 P/N 211560H 8. 8. Insert caps (8) into end of each support arm (9 & 10) as shown. Tap firmly in position. 9. Apply logo label (11) to lower support arms (10) as shown. Repeat for opposite side. Beginning with upper support arms (9) secure TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING support arms to pole. Continue by securing lower support arms (10) as shown. IMPORTANT! Do not over tighten. SHORT END 9 10 11 10 8 8 8 8 12 7 4 4 9 5 4 4 10. 7 7 4 8 8 Note: This bolt rests outside the upright pole. 12 4 4 4 P/N 211560H 01/03 6 11. 16 4 13 9 4 7 4 10 7 4 10 7 4 16 4 7 4 9 16 4 16 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPORTANT! Do not over tighten. 14 14 14 1514 13 14 Cut foam stripping (14) to sizes shown and attach to flat side of H-frame (13) as shown. Then secure H-frame to support arms (9 & 10). NOTE: Install H-Frame (13) with foam striping toward backboard. Do this strip last. 11. 16 4 13 9 4 7 4 10 7 4 10 7 4 16 4 7 4 9 16 4 16 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPORTANT! Do not over tighten. 14 14 14 1514 13 14 Cut foam stripping (14) to sizes shown and attach to flat side of H-frame (13) as shown. Then secure H-frame to support arms (9 & 10). NOTE: Install H-Frame (13) with foam striping toward backboard. Do this strip last. 7 01/03 P/N 211560H Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rotating. Rotate handle clockwise on crank jack to the fully extended position. Upright crank jack. 12. Secure jack brackets (17 & 18) to lower holes in pole as shown. 13. IMPORTANT! HOLD HERE 20 7 4 17 4 18 19 19 4 4 7 12. Secure jack brackets (17 & 18) to lower holes in pole as shown. 13. IMPORTANT! HOLD HERE 20 7 4 17 4 18 19 19 4 4 7 P/N 211560H 01/03 8 46 14. Install crank jack (20) U-joint to lower set of support arms (10) as shown. 10 4 20 7 4 12 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPORTANT! Do not over tighten. 46 14. Install crank jack (20) U-joint to lower set of support arms (10) as shown. 10 4 20 7 4 12 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPORTANT! Do not over tighten. REAR VIEW 9 01/03 P/N 211560H 15. 19 17 20 4 21 21 7 4 18 15. 19 17 20 4 21 21 7 4 18 WARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. Rotate jack handle clockwise to raise H-frame (13) to approximately 7’ (2.1 m) from ground. Secure crank jack (20) to jack brackets (17 &18) as shown. NOTE: Some adjustment will be necessary to align the lower crank jack bushing to jack brackets (17 & 18). REAR VIEW P/N 211560H 01/03 10 16. 16. While H-frame (13) is in the lowest position, hang backboard onto H-frame (13). NOTE: Backboard frame will rest on top of H-frame. Secure backboard with hardware as shown. *ONLY Fingertighten bolts (22) with nuts (23). Repeat procedure for opposite side. 23 22 13 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAM...

Descargar ahora

Introduzca dos números de la imagen: