Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
Pull the Wire Harness (48) out of the Frame (2) and insert it upward through the Upright (6). Do not let the Wire Harness fall into the Upright; use a piece of tape or an elastic band to hold the Wire Harness in place until step 12. Insert the Upright (6) into the Frame (2). Attach the Upright with three M8 x 16mm Button Screws (95) and three Star Washers (100). Avoid pinching the Wire Harness (48) between the Upright and the Frame. 4 5. Identify the Left Roller Leg (12), which is marked 5 with a “Left” sticker. Orient the Left Roller Leg as shown near the left Crank Arm (36). Apply a small amount of the included grease to both sides of a Wave Washer (98). Also, apply grease to the Roller (22) on the Left Roller Leg (12); spread the grease evenly around the Roller. Slide the Wave Washer (98) onto the left Crank Arm (36). Next, slide the Left Roller Leg (12) onto the Crank Arm and set the Roller (22) on the Base (1). Attach the Left Roller Leg with an M10 x 23mm Shoulder Screw (80), an M10 x 20mm x 1.5mm Washer (84), and a Crank Axle Cap (30). Repeat this step to attach the Right Roller Leg (21) to the right Crank Arm (not shown). 6 95 95 100 2 95 100 48 36 1 84 30 98 22 Grease 80 12 21 Grease 7 6 6. Identify the Left Handlebar (8), which is marked with a “Left” sticker. Insert the Left Handlebar into one of the Handlebar Legs (11) as shown. Attach the Left Handlebar (8) with two M8 x 42mm Bolts (71) and two M8 Nylon Locknuts (96). Make sure that the Nylon Locknuts are inside the hexagonal holes. Assemble the Right Handlebar (not shown) and the other Handlebar Leg (not shown) in the same way. 11 71 8 96 Hexagonal Hole Hexagonal Hole 7. Position an Inner Handlebar Cover (18) and an Outer Handlebar Cover (19) around the Left Handlebar (8) as shown. Attach the Inner and Outer Handlebar Covers (18, 19) with three M4 x 16mm Self-tapping Screws (79) and an M4 x 13mm Washer (93). Start all three Self-tapping Screws before tightening them. Repeat this step for the Right Handlebar (not shown). 7 19 18 79 79 8 93 8 8. Apply a generous amount of grease to the Pivot 8 Axle (65) and insert it into the Frame (2). Attach the two Frame Covers (17) to the Frame (2) with four M4 x 16mm Screws (86) as shown. 9. Apply a small amount of grease to both sides of 9 a Wave Washer (98). Slide the Wave Washer onto the left side of the Pivot Axle (65). Next, slide the Left Handlebar (8) onto the Pivot Axle as shown. Attach the Left Handlebar (8) with an M10 x 23mm Shoulder Screw (80) and an M10 x 20mm x 1mm Washer (81). Repeat this step to attach the Right Handlebar (9) to the Pivot Axle (65). 86 86 65 17 17 2 Grease 98 9 81 8 80 65 Grease 9 10. Identify the Left Pedal (13) and the Left Pedal 10 Leg (14), which are marked with “Left” stickers, and orient them as shown. Attach the Left Pedal (13) to the Left Pedal Leg (14) with four M6 x 35mm Phillips Screws (87) and four M6 Split Washers (88). Start all four Phillips Screws before tightening them. Repeat this step to attach the Right Pedal (not shown) to the Right Pedal Leg (not shown). 88 88 13 14 87 87 11. Apply a generous amount of grease to two Pedal Leg Axles (32). Insert one Pedal Leg Axle into the bottom of the left Handlebar Leg (11). Insert the other Pedal Leg Axle into the left Roller Leg (12). Apply a small amount of grease to both sides of two Wave Washers (98). Place a Wave Washer on each Pedal Leg Axle (32). Orient the Left Pedal Leg (14) as shown, and slide it onto the Pedal Leg Axles (32). Attach the Left Pedal Leg to the left Handlebar Leg (11) with two M10 x 23mm Shoulder Screws (80), two M10 x 20mm x 2mm Washers (92), and two Axle Caps (31). Attach the Left Pedal Leg (14) to the left Roller Leg (12) with two M10 x 20mm Button Screws (91) and two M10 x 25mm Washers (94); do not overtighten the Button Screws. The Legs (11, 14, 12) must be able to pivot freely. Repeat this step for the Right Pedal Leg (not shown). 92 91 14 9480 31 32 31 11 80 12 94 91 92 32 11 Grease 98 Grease 98 10 11 12. The Console (5) requires four 1.5V “D” batteries (not included); alkaline batteries are recommended. IMPORTANT: If the elliptical exerciser has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries into the Console. If you do not do this, the console displays or other electronic components may become damaged. See the inset drawing. Remove the battery cover from the Console and insert four batteries into the Console. Make sure that the batteries are oriented as shown by the diagram in the battery compartment. Then, reattach the battery cover. Note: The Console (5) can be operated with an optional power supply instead of batteries. To purchase a power supply, call the telephone number on the front cover of this manual. Plug one end of the power supply into the jack on the console. Plug the other end of the power supply into an appropriate outlet that is properly installed in accordance with all local codes and ordinances. Have a second person...
Otros modelos de este manual:Formadores - 510 (907.44 kb)