Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Use the same + or – arrows to select the speed for your workout. Press ENTER PROGRAM. 3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline. Press ENTER PROGRAM. To start, press the START/STOP button. To access P2 mode, press the selected program button three times (once for OP, twice for P1, three times for P2). Follow the above steps 1-3 to customize P2 settings. ¦ TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you haveprogrammed the P1 or P2 modes, you will need to use the PAUSE button to change the program youpreviously entered. For instance to change to a new setting in P1-FAT BURN, press the FAT BURN button twice to access P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above to continue to change the program. FAT BURN CARDIO WARM UP CROSS TRAINING USER PROGRAM INCLINE START/STOP POWER PAUSE PAGE 14 Program Instructions Heart rate See page 16 for pictures and diagrams EC6500HR ONLY HEART RATE MONITOR MODE The treadmill may at any time be used in the Heart Rate Monitor Mode. If the signal from the chest strap is detected, heart rate BPM will be displayed in the INCLINE window. The incline will only be briefly displayed if manual or program changes are initiated. The Heart Rate program is designed to keep your heart at a desired amount of “beats per minute” by automatically adjusting the incline. For example, you have programmed in a desired heart rate of 125 BPM and your heart rate is only at 110 BPM. If you are wearing the Heart Rate Transmitter, correctly the incline will automatically increase to intensify the work load, causing your heart rate to slowly climb to 125 BPM. The treadmill will attempt to maintainyour target heart rate through adjustments to the incline for the remainder of your workout. In the same respect, if your heart rate is above your programmed amount of BPM’s, the incline will automatically decrease to lower your heart rate. You may at any time during the Heart Rate Program adjust/override the speed and/or the incline by simply pressing the correct corresponding button. You may also change your “Target Heart Rate” at any time by pressing the TARGET UP or TARGET DOWN button. HEART RATE PROGRAM OPERATION ¦ Plug treadmill into a surge protector outlet. Attach the Red Safety Key on to the treadmill console. ¦ Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. ¦ Press POWER button. Place the Heart Rate Transmitter strap across your chest and connect ends. (Make sure your skin is moist and the strap is snug for accurate transmission). At this time, if the display is receiving a signal from the chest strap, the incline window will begin to settle on your current heart rate. ¦ Press the HEART RATE CONTROL button to enter the electronics into the Heart Rate Program. Theincline window will momentarily flash ‘125’, which is the default program target heart rate. ¦ The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. PressENTER PROGRAM. ¦ The SPEED/TIME window will then blink. Use the same + or – arrows to select the speed for your workout. Press ENTER PROGRAM. ¦ The incline window (if receiving your heart rate accurately) will show current BPM, and the small red light labeled PULSE adjacent to the incline window, will be illuminated. (If the receiver is not receiving an accurate reading, the incline window will be flashing - - - -). ¦ To adjust the pre-set target heart rate press the TARGET +/TARGET– button then press the ENTER PROGRAM button. ¦ Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving. The small light at the top of the console labeled TARGET will be illuminated if you are at your target. If you are not, the arrow shaped lights will illuminate and reflect if you are above or below your goal. Ifyou are not within 25 BPM of your “Target heart rate” the program will not work. DO NOT STOP TO START OVER. Continue exercising and your heart rate will naturally increase. The program will continually monitor your heart rate and periodically adjust the incline up or down to increase or decrease the resistance thereby keeping you at your target zone. At the conclusion of the programmed time the TIME window will flash 00:00 and the CALORIES/DISTANCE window will continue to accumulate values. The treadmill will continue operation until the START/STOP button or the PAUSE button is pressed. Press thePOWER button to turn off the treadmill. PAGE 15 Program Instructions Heart rate WORKOUT TIME TARGET ARROWS TARGET UP TARGET DOWN CALROIES/DISTANCE START/STOP POWER PAUSE INCLINE WINDOW HEART RATE CONTROL ENTER PROGRAM PAGE 16 1 2 1 1 1 0 9 8 7 6 5 4 Program Profiles 1 2 3 4 5 6 7 8 9 10 SPEED INCLINE The Fat Burn Program is designed to vary the treadmill elevation, while main- taining a constant walking belt speed. 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 SPEED INCL...
Otros modelos de este manual:Formadores - Encore 4500 (1.72 mb)