Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Impex Tamaño del archivo: 4.68 mb Nombre del archivo: bda31211-1f37-4d47-b7dd-baa2ac699e91.pdf Idioma del manual:

Do not tighten the Locknuts yet. 12 13 14 15 82 98 98 31 112 36 91 5 91 91 91 26 36 91 112 31 82 98 98 91 91 91 98 98 85 14 14 90 23 23 15 7 6 74—Grease Grease Grease 100 2 5 Arm Assembly 11 16. Attach the Leg Bumper (59) to the Right Seat Frame (3) with an M4 x 16mm Self-tapping Screw (89) and an M4 Washer (96). Grease an M10 x 75mm Bolt (60). Attach the Leg Lever (4) to the Right Seat Frame (3) with the Bolt and an M10 Nylon Locknut (90). Make sure the “U”-rod is on the indicated side of the Leg Lever. Do not overtighten the Locknut; the Leg Lever must be able to pivot easily. 18. Attach a Press Handle (32) to a Press Arm (30) with an M10 x 65mm Bolt (77), two M10 Washers (99), two M10 x 12mm Spacers (101), and an M10 Nylon Locknut (90). Attach a Press Arm Cap (34) to the Press Arm (30) with an M10 x 45mm Button Bolt (81) and an M10 Large Washer (100). Repeat this step with the other Press Arm (30). 17. Grease an M10 x 108mm Bolt (72). Orient the Press Frame (29) as shown. Attach the Press Frame to the Left Base (25) with the Bolt and an M10 Nylon Locknut (90). Do not overtighten the Locknut; the Press Frame must be able to pivot easily. 16 17 18 4 96 59 89 90 60 3 Grease 29 72 90 Grease 25 30 34 32 100 30 77 99 99 90 101 101 81 “U”-rod 12 19. Attach a Press Arm (30) to the Press Frame (29) with two M8 x 69mm Bolt (86) and two M8 Nylon Locknuts (91). Repeat this step with the other Press Arm (30). 21. Grease an M10 x 77mm Bolt (76). Attach the Foot Plate (38) to the Leg Press Frame (28) with the Bolt and an M10 Nylon Locknut (90). Make sure the decal on the Foot Plate is right side up. Do not overtighten the Locknut; the Foot Plate must be able to pivot easily. 20. Grease an M10 x 108mm Bolt (72). Attach the Leg Press Frame (28) to the Left Base (25) with the Bolt and an M10 Nylon Locknut (90). Do not overtighten the Locknut; the Leg Press Frame must be able to pivot easily. 19 20 21 22 30 30 86 91 29 28 90 72 25 38 28 76 90 Grease 28 91 37 109 22. See the CABLE DIAGRAMS on pages 26 and 27 as you assemble the cables and to identify the cables. Locate the Press Cable (109). Attach the Cable to the Leg Press Frame (28) with an M8 x 86mm Shoulder Bolt (37) and an M8 Nylon Locknut (91). Cable Assembly 13 23. Wrap the Press Cable (109) around a 90mm Pulley (63). Attach the Pulley, two Half Finger Guards (66), a Cable Trap (68), and an M10 Washer (99) to the Left Seat Frame (27) with an M10 x 103mm Bolt (22) and an M10 Nylon Locknut (90). Make sure the Cable Trap and the Finger Guards are oriented as shown. 25. Wrap the Press Cable (109) around a 90mm Pulley (63). Attach the Pulley, two Half Finger Guards (66), a Cable Trap (68), and an M10 Washer (99) to the Left Upright (26) with an M10 x 108mm Bolt (72) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 26. Wrap the Press Cable (109) around a 90mm Pulley (63). Attach the Pulley, two Half Finger Guards (66), a Cable Trap (68), and an M10 Washer (99) to the Press Frame (29) with an M10 x 135mm Bolt (70). Make sure the Cable Trap and Finger Guards are oriented as shown. 24. Wrap the Press Cable (109) around a “V”-pulley (62). Attach the “V”-pulley, two Half Finger Guards (66), and two M10 Washers (99) to the Leg Press Frame (28) with an M10 x 115mm Bolt (71) and an M10 Nylon Locknut (90). Make sure the Finger Guards are oriented as shown. 23 24 25 26 90 99 66 63 109 66 68 22 27 66 66 99 109 99 62 90 28 71 66 66 90 72 26 109 63 99 68 70 66 109 66 29 68 63 99 14 27. Wrap the Press Cable (109) around a “V”-pulley (62). Attach the “V”-pulley, two Half Finger Guards (66), a Large Cable Trap (111), and an M10 Washer (99) inside the bracket on the Left Upright (26) with an M10 x 65mm Bolt (77) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 29. Wrap the Press Cable (109) under a 90mm Pulley (63). Attach the Pulley, two M10 Washers (99), and two Half Finger Guards (66) inside the bracket on the Left Base (25) with an M10 x 50mm Bolt (64) and an M10 Nylon Locknut (90). Make sure the Finger Guards are oriented as shown. 30. Wrap the Press Cable (109) over a 90mm Pulley (63). Attach the Pulley and a Cable Trap (68) to the Right Top Frame (5) with an M10 x 45mm Bolt (80) and an M10 Nylon Locknut (90). Make sure the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 28. Wrap the Press Cable (109) around a 90mm Pulley (63). Attach the Pulley, two Half Finger Guards (66), a Cable Trap (68), and an M10 Washer (99) to the Press Frame (29) with the M10 x 135mm Bolt (70) used in step 26 and an M10 Nylon Locknut (90). Make ...

Descargar ahora

Introduzca dos números de la imagen: