Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. 3 HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size. 4 ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches. NOTE: It is strongly recommended two or more people assembling this equipment to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left & Right Upright Beams (#1 & #19) by a Cross Brace (#2) in the mid-span. Secure them with two M10 x 2 .” Hex Bolts (#38), one Bracket (#16), two . .” Washers (#44), and two M10 Aircraft Nuts (#47) on each end of the Cross Brace. B.) Insert the Backrest Adjustment Bar (#8) through a selected hole on the Upright Beams to obtain desired incline of Backrest. C.) Insert Left & Right Bar Catches (#7) & (#6) into the selected holes on the Upright Beams to obtain the desired height to hold the weight bar. DIAGRAM 1 5 STEP 2 (See Diagram 2) A.) Connect the Front Stabilizer (#5) to the Main Seat Support (#3) and secure them with three M8 x 5/8” Hex Bolts (#41) and O 5/8” Washers (#45). DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support to the Cross Brace (#2). Secure it with two M10 x 2 1/8” Bolts (#39), one Bracket (#16), two . .” Washers (#44), and two M10 Aircraft Nuts (#47). DO NOT tighten the nuts and bolts yet. C.) Connect one end of the Diagonal Support (#4) to the Main Seat Support. Secure it with one M8 x 2 1/8” Hex Bolt (#42), one . 5/8” Washer (#45) and one M8 Aircraft Nut (#48). Connect the other end to the Front Stabilizer. Secure it with one M8 x 5/8” Hex Bolt (#41) and one . 5/8” Washer (#45). D.) Securely tighten all the nuts and bolts previously installed. DIAGRAM 2 6 STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#9) to the open bracket on the Front Stabilizer (#5). Secure it with one M10 x 2 .” Hex Bolt (#38), O .” Washer (#44), and M10 Aircraft Nut (#47). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Tubes (#10) halfway through the holes on the Leg Developer. Push four Foam Rolls (#35) onto the Tubes from both sides. C.) Attach a Spring Clip (#36) onto the weight post on the Leg Developer. DIAGRAM 3 7 STEP 4 (See Diagram 4) A.) Attach the Backrest Supports (#14) onto both ends of the Pivot on the Main Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#8). B.) Place the Backrest Board (#17) onto the Backrest Supports. Secure it with four M6 x 1 .” Hex Bolts (#43) and . .” Washers (#46). C.) Place the Seat Pad (#18) onto the bracket on the Main Seat Support (#3). Align the holes and secure it with four M6 x 1 .” Hex Bolts (#15) and . .” Washers (46). D.) Thread the Lock Knob (#37) into the Front Stabilizer (#5). DIAGRAM 4 8 STEP 5 (See Diagram 5) A.) Attach the ball end of the Cable (#33) to the Pulley (#30). Place the Pulley in the open slot on the Upper Lat Bar Frame (#52). Secure it with one M10 x 2” Hex Bolt (#40), two Pulley Bushings (#29), and one M10 Aircraft Nut (#47). B.) Slide the Weight Holder (#11) onto the Lat Bar Frame. C.) Insert the Lower Lat Bar Frame (#12) into the Upper Lat Bar Frame. Secure them together with four M8 x 5/8” Hex Bolts (#41) and four O 5/8” Washers (#45). D.) Connect the Lat Bar (#13) to the Cable with a Hook (#32). Place the Lat Bar Frame onto the storage post behind the Left Upright Beam. When using the Lat Pull Down, insert the Lat Bar Frame into the opening on the Front Stabilizer and use the Lock Knob (#37) to hold it in position. E.) Connect the Cable to the Weight Holder (#11) with a Hook (#32). 9 10 PARTS LIST KEY NO. DESCRIPTION QUANTITY Left Upright Beam 1 Cross Brace 1 Main Seat Support 1 Diagonal Support 1 Front Stabilizer 1 Right Bar Catch 1 Left Bar Catch 1 Backrest Adjustment Bar 1 Leg Developer 1 Foam Tube 2 Weight Holder 1 Lower Lat Bar Frame 1 Lat Bar 1 Backrest Support 2 M6 x 1 .” Hex Bolt 4 Bracket 3 Backrest Board 1 Seat Pad 1 Right Upright Beam 1 Weight Bar 1 2’ Square End Cap 2 1” x 2” End Cap 6 1 .” End Cap 1 1 .” End Cap 4 O .” End Cap 4 O 1” End Cap 7 O .” Bar Catch End Cap 2 Lat Bar Grip 2 Pulley Bushing 2 Pulley 1 Sleeve 3 Hook 2 Cable 1 Leg Developer Spacer 2 Foam Roll 4 Spring Clip 3 Lock Knob 1 M10 x 2 .” Hex Bolt 5 M10 x 2 1/8” Hex Bolt 2 M10 x 2” Hex Bolt 1 M8 x 5/8” Hex Bolt 8 M8 x 2 1/8” Hex Bolt 1 M6 x 1 .” Hex Bolt 4 O .” Washer 7 O 5/8” Washer 9 O .” Washer 8 M10 Aircraft Nut 8 M8 Aircraft Nut 1 1” Square End Cap 2 25 lbs Weight Plate 2 15 lbs Weight Plate 2 Upper Lat Bar Frame 1 11 IMPEX® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or...