Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
24 1 206940 Axle 58 2 204859 Cover, Pin Slide 25 2 206938 Push Cap 59 1 204853 Lanyard, Black Coil 26 1 206605 Handle, Front Plastic 60 1 204850 Pin, Locking 27 4 204804 Screw, Phillips Head, 3/4” Long 61 1 Rim 28 1 206956 Disc, 5” O.D. x 13/32 I.D., plastic 62 1 204290 Net 29 2 900846 Board Bracket 63 1 206990 Reinforcement Bracket 30 2 201129 Spacer, .500 O.D. x 1.8 Long 64 1 200628 Wheel Axle, 11 3/4 Long 31 1 240017 Bolt, Hex Head, 1/4-20 x 2-1/4 Long 65 1 200627 Wheel Carriage 32 1 203493 Nut, 1/4-20, Center Lock 66 2 203217 Carriage Bolt, 5/16-18 x 1 1/2 Long 33 3* 206360 Bolt, Hex Head, 3/8-16 x 2-5/8 Long 34 4* 201124 Lock Nut, Hex Head, 3/8-16 Items not used with this model 67 2 200874 Spacer, Steel .402 I.D.x.50 O.D.x1.5 Long 68 2 201642 Spacer .530 I.D. x.63 O.D. x .63 Long * You may have extra parts with this model. 7 01/04 P/N 211948C P/N 211948C 01/04 8 Item #10 (3) Item #14 (11)* Item #15 (1) Item #16 (2) Item #8 (1) Item #19 (1) Item #22 (4) * You may have extra parts with this model. HARDWARE IDENTIFIER (CONTINUED) HARDWARE IDENTIFIER (BOLTS & SCREWS) HARDWARE IDENTIFIER (NUTS) Item #18 (2) Item #31 (1) Item #39 (3) Item #50 (1) Item #33 (3) Item #27 (4) Item #12 (1) Item #36 (6) Item #32 (1) Item #38 (6) Item #34 (4) Item #54 (2) HARDWARE IDENTIFIER (METAL RODS, SPACERS & WASHERS) Item #30 (2) Item #55 (2) Item #57 (4) Item #13 (11) Item #7 (1) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) * You may have extra parts with this model. Item #37 (8) Item #43 (12) Item #6 (2) ITEMS NOT USED WITH THIS MODEL Item #68 (2) Item #67 (2) 9 01/04 P/N 211948C SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) Item #10 Item #14Item #15 Item #16 Item #19 Item #22 Item #18 Item #39Item #50 Item #33 Item #27 Item #12 Item #34 Item #54 Item #55 Item #57 Item #13 Item #6 AND/OR 9/16”1/2” Socket Extension (2) Socket Wrenches and Sockets (2) 1/2” AND (2) 9/16" Wrenches 10 P/N 211948C 01/04 1. 1. Install wheel axle (64) through wheel carriage (65) and install wheels (5) onto wheel axle (64) with spacers (6) as shown. Secure wheel bracket as shown, a deep socket is recommended. 18 13 34 IMPORTANT!: DO NOT OVER TIGHTEN 64 6 65 5 65 2. Mark pole sections with tape as shown. MIDDLE TOP 1 2 5" (13 cm) BOTTOM 5" 3 (13 cm) 11 01/04 P/N 211948C IMPORTANT! Center alignment slot of middle pole section (2) in a lower hole of top pole section (1) as shown. While maintaining alignment, bounce pole top (1) and middle section (2) together as shown until they no longer move toward taped reference mark. Upright assembly. 3. WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 3. WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 2 1 4. IMPORTANT! Center alignment slot of lower pole section (3) in a lower hole of middle pole section (2) as in step 3. While maintaining alignment, bounce assembly and lower pole section (3) together as shown until they no longer moved toward taped reference mark. POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 2 3 WOOD SCRAP (NOT SUPPLIED) 1 12 P/N 211948C 01/04 5. 5. Install rod (7) through holes in bottom pole section (3) and eyebolt (8). Insert pole assembly into tank assembly as shown. Secure pole assembly with upper pivot bracket (9) 8 7 1 3 2 6. and lock nut (10). 9 10 4 3 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 13 01/04 P/N 211948C 7. 12 13 13 11 3 3 11 4 11 15 Secure base struts (11) to pole using bolt (12), washers (13), and nut (15) as shown. TIGHTEN BOLT (9) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! Rotate the non-secured ends of base struts (11) as shown. 12 13 13 11 3 3 11 4 11 15 Secure base struts (11) to pole using bolt (12), washers (13), and nut (15) as shown. TIGHTEN BOLT (9) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! Rotate the non-secured ends of base struts (11) as shown. CAREFULLY TIPPING THE SYSTEM FORWARD WILL ALLOW EASIER ACCESS TO UNDERSIDE OF BASE NOTE: 8. 16 11 13 4 13 14 Secure base struts (11) to base using bolt (16), washers (13), and nut (14). 14 P/N 211948C 01/04 9. 9. 10. 18 13 17 28 21 13 10 22 as shown. Tighten completely. 20 14 12. 25 5 24 5 25 10 13 19 13 13. 13. Carefully reposition entire assembly as shown. 14. Attach front of plastic handle (26) to back of plastic handle (23) around handle bar (20) using self- tapping screws (27) as shown. IMPORTANT! Front of plastic handle (26) should face outward, away from pole assembly. FRONT SIDE 27 23 20 26 16. Install pole mount bracket (53) and reinforcement bracket (63) with carriage bolts (54) as shown. Tighten flange nuts (14) completely. Insert bolts (66) through plastic handle assembly, handle bar (20), and attach nuts (14) as shown. ...