Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
BOLT............................... 2. 3/8X3 IN. BOLT............................... 3. 3/8 IN. WASHER................................ 4. 3/8 IN. LOCK NUT ............................ 5. 2-3/8 IN. CABLE RETAINING CLIP 6. 2-7/8 IN. CABLE RETAINING CLIP 7. 2 IN. SQ PARABODY COVER CAP 8. 3-1/2 X 1 IN. PULLEY....................... NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH RULER: 1/2 I 1/2 1/2 1 1/2 I 1/2 I 1/2 0 I 1 1 I I I.....JL 2 I 3 ■ I I 1 1 » 4 I 5 I I III_L Part# 6638101 1 Revision: 06/03/96 NOTE: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. THE LEG PRESS ATTACHMENT (832101) MUST BE ASSEMBLED BEFORE ASSEMBLING IT TO THE PARABODY 350. PLEASE ASSEMBLE THE LEG PRESS ATTACHMENT AT THIS TIME USING THE 832 PRODUCT ASSEMBLY INSTRUCTIONS. Insert two (2) 2 SQ. IN. PARABODY COVER CAPS onto the BASE CONNECTION WELDMENT as shown on drawing. Remove middle 4-1/2 X 1 IN. PULLEY, 3/8.X 1-3/4 IN. BOLT, and 3/8 IN. LOCK NUT from the 350 BASE. Remove the SECONDARY (LOWER) CABLE from the 350. NOTE: The SECONDARY (LOWER) CABLE will no longer be needed. SECURELY assemble the BASE CONNECTION WELDMENT to the 832 using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. LOCK NUTS. LOOSELY assemble one (1) 4-1/2 X 1 IN. PULLEY, from step 2, to the lower hole on the: right side of the BASE CONNECTION WELDMENT using one (1) 3/8 x 2 IN. BOLT, one (1) 2-7/8 [N. CABLE RETAINING CLIP, and one (1) 3/8 IN. LOCK NUT. LOOSELY assemble one (1) 3-1/2 X 1 IN. PULLEY to the upper hole on the left side of the BASE CONNECTION WELDMENT using one (1) 3/8 x 2 IN. BOLT, one (1) 2-3/8 IN. CABLE RETAINING CLIP, and one (1)3/8 IN. LOCK NUT. - . LOOSELY assemble one (1) 3-1/2 X 1 IN. PULLEY to the middle pulley flat of the 350 BASE using one (1) 3/8 x 2 IN. BOLT, one (1) 2-3/8 IN. CABLE RETAINING CLIP, and one (1) 3/8 IN. LOCK NUT. SECURELY attach the BASE CONNECTION WELDMENT and the 832 to the base of the 350 using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. LOCK NUT S. Following the cable routing diagram, thread the LEG PRESS CABLE from the SWIVEL LOW ROW through the BASE CONNECTION WELDMENT and around the pulley in the 832. (The: pulley, wheels, and spacers may need to be temperately removed) and to the cam on the LEG CURL/EXT. SECURE end of LEG PRESS CABLE to the cam using the hardware removed in step 3. SECURELY tighten all pulley connections, making sure that the CABLE RETAINING CLIPS are facing the correct direction as shown in drawing. - If upon completion of assembly, the head plate does not sit on top of first weight plate or there is excess slack in the cable system, refer to your 350 ASSEMBLY INSTRUCTIONS. (NOTE: Some slack in the cable system is needed to allow for pre-stretch adjustment in the 832 leg press.) Part# 6638101 2 Revision: 06/03/96 i I CUSH NO DESCRIPTION REVISIONS 01 AS SHOWN R£Y DESCffiPtXM CHG HO APPÛ OATZ 3-1/...
Otros modelos de este manual:Formadores - 350104 (180.34 kb)