|
Resumen del manual
' Also enter this serial number on your Warranty Card. 5 0 § T 1 TOOLS INCLUDED PARTS INCLUDED □ 5mm Allen Wrench □ 1 Console EX-22: □ 4mm Alien Wrench □ 1 Console Mast □ 4HardwareBags □ PhillipsScrewDriver □ 1 Front StabilizerTube EX-33, EX-44: □ 13/15mmFlatWrench □ 2UpperHandlebars □ lAccessoryTray □ 17mmFlatWrench □ 2LowerHandlebars □ 2PerimeterBars □ 2LowerLinkArms □ 3StabilizerCovers □ 2PivotingFootPads □ 2HandlebarCovers □ 2 Top Side Covers □ EX-33:5HardwareBags □ 1 PowerSupply □ EX-44:6HardwareBags □ EX-44:2ElbowCovers Ifyou have questions orif there are anymissing parts, we guarantee complete satisfaction. CustomerTech Support contactinformation is located on the back panel of this manual. ASSEMBLY STEP 1 53 § Ft QcO car* Ok A) Open HARDWARE BAG FOR STEP 1. o=£5 B) Attach the FRONT STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 WASHERS (B) and 2 WASHERS (C). by -a «g P s£i 3l ca oca o |g JoK Oq«^ ê11 PC0» ASSEMBLY STEP 2 A) Open HARDWARE BAG FOR STEP 2. B) Carefully pull the CONSOLE WIRES through the CONSOLE MAST using the twist tie located inside the CONSOLE MAST. C) Attach the CONSOLE MAST to the MAIN FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT WASHERS (C). Ft QcO 05* §C= Ok $3 °°s D) Insert the left TOP SIDE COVER, followed by the right TOP SIDE COVER and snap them together. E) EX-33 & EX-44 only: Insert ACCESSORY TRAY and secure it using 2 SCREWS (K) as shown. F) Slide CONSOLE MAST GROMMET down to seal the console mast hole. cSS2 SrE* E Is oca o S toK PC08 i«= ASSEMBLY STEP 3 (EX-33 & ex-44 only) NOTE: EX-22 SKIP THIS STEP A) Open HARDWARE BAG FOR STEP 3. B) Attach the PERIMETER BARS using 4 BOLTS (L). C) Attach REAR STABILIZER COVER using 2 SCREWS (M). D) Attach FRONT STABILIZER COVERS using 2 SCREWS (M) for each side. HARDWARE BAG FOR STEP 3 CONTENTS : BOLT (L) 45 mm Qty:4 SCREW (M) 10 mm Qty:6 ASSEMBLY STEP 4 NOTE: There is NO hardware bag for this step. All hardware is pre-installed. A) Remove PRE-ATTACHED BOLT & WASHERS from CONSOLE MAST. B) Slide LOWER HANDLEBARS onto CONSOLE MAST and attach by re-inserting PRE-ATTACHED BOLT & WASHERS. C) Slide UPPER HANDLEBARS onto LOWER HANDLEBARS and align NOTCH with TAB making sure handlebars are joined together completely. Secure UPPER HANDLEBARS to LOWER HANDLEBARS using PRE-ATTACHED SET SCREWS. Awarning After handlebars are assembled they will rotate freely - be cautious. Until the machine is fully assembled, do not grab the handlebars for support. ASSEMBLY STEP 5 (EX-33 & ex-44 only) NOTE: EX-22 SKIP THIS STEP NOTE: There is NO hardware bag for this step. A) Snap the front and back HANDLEBAR COVERS together onto the UPPER HANDLE BARS. Note the position of the snap tabs on the covers before snapping into position. B) Repeat on other side. EX-33 & EX-44 ONLY ASSEMBLY STEP 6 53 Ft E B) Slide LOWER LINK ARM into bottom end of LOWER HANDLEBAR. Slide BOLT (E) through outside hole in LOWER HANDLEBAR, through 1 TEFLON WASHER (F), SPACER (G) and another TEFLON WASHER (F). Secure using NUT (H). C) Repeat on other side. ASSEMBLY STEP 7 3 § TT BOLT(G) —TEFLON WASHER (E)— _____ - FOOTPLATETUBE FLAT WASHER (C) SPACER (F) TOP VIEW OF LEFT FOOT PAD A ) Open HARDWARE BAG FOR STEP 7. B) Align LOWER LINK ARM with U BRACKET. CAUTION: Be careful to keep the LOWER LINK ARM aligned with guide rail. Do not twist it to the left or right while positioning it on the U BRACKET. C) Insert 2 TEFLON WASHERS (E) on left and right sides of FOOT PLATE TUBE before sliding SPACER (F) through U BRACKET and FOOTPLATE TUBE. D) Insert FLAT WASHER (C) and BOLT (G) into outside end of FOOTPLATE TUBE to secure LOWER LINK ARM to PEDAL ARM. E) Repeat on other side. ASSEMBLY STEP 8 (EX-44 only) 53 § Ft Qc53 car* OkF^ Ok §§ °°s NOTE: EX-22 & EX-33 SKIP THIS STEP A) Open HARDWARE BAG FOR STEP 8. B) Attach the OUTSIDE ELBOW COVER to elbow joint using 1 SCREW (L). C) Snap the INSIDE ELBOW COVER onto the OUTSIDE ELBOW COVER. Note the position of the snap tabs before snapping into position. D) Repeat on other side. sSS HARDWARE BAG FOR STEP 8 CONTENTS : EX-44 ONLY A SCREW (L) |] 10 mm \ Qty:2 C3 Is oca o |S OQ«^T ê11 PC** i«= ASSEMBLY STEP 9 || s?i Si CiEn is CONSOLE CONSOLE MAST EX-22 CONSOLE PRE-ATTACHED SCREWS CONSOLE WIRES NOTE: There is NO hardware bag for this step. All hardware is pre-installed. A) Attach the CONSOLE MAST wires to the CONSOLE wires . B) Carefully tuck the CONSOLE MAST wires into the CONSOLE MAST before attaching the CONSOLE. C) Attach CONSOLE to the CONSOLE MAST using the 4 PRE-ATTACHED SCREWS (screws will have to be removed from the console first). DO NOT PINCH WIRES! es * i P sü STD BEFORE YOU BEGIN 53 Ft CONGRATULATIONS! on choosing your elliptical. You’ve taken an important step in developing and sustaining an exercise program! Your elliptical is a tremendously effective tool f...
Otros modelos de este manual:Formadores - HZ SERIES EX-22 (2.01 mb)
Formadores - HZ SERIES EX-33 (2.01 mb)