Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
EML E-Series
HP
e2400-FC 2Gb
Interface
StorageWorks
Controller
Replacement
Caution: Before continuing with this
Note: This part is NOT hot-pluggable.
procedure, make sure the following
You must power down the library to
components are upgraded to the latest
replace this part.
firmware versions:
• Library
• Interface Manager
• Command View TL
Note: You can find an animation of the
Refer to the HP StorageWorks Interface
removal process on the documentation CD
Manager and Command View TL User
that shipped with the tape library.
Guide for detailed procedures on checking
versions and making updates.
Caution: Parts can be damaged by
electrostatic discharge. Keep parts in their
containers until needed. Ensure that you
are properly grounded when touching
static sensitive components.
1
2
EML
e2400-FC 2G
Interface
HP
Controller
StorageWorks
Upgrade
Caution: Parts can be damaged by
electrostatic discharge. Keep parts in their
containers until needed. Ensure that you
are properly grounded when touching
Caution: Before continuing with this
static sensitive components.
ry firmware
procedure, ensure the following components
are upgraded to the necessa
versions:
• Library:
er:
• Interface Manag
Note: This part is not hot-pluggable.
• Command View ESL:
It is necessary to power down the library
to replace this part.
Refer to the HP StorageWorks Interface
and Command View User Guide
Manager
for detailed procedures on checking
f
irmware revisions and making updates.
Note: You will find an animation of
this procedure on the documentation
CD shipped with your library..
1
ES
L
E
-
s
eries
In
t
erface
Manager
h
p
1
0
0
2
6
N
o
te: This part is not hot-pluggable.
I
t
i
s necessary to power down the library
S
to
rageWorks
t
o
r
eplace this part.
C
a
ution: Parts can be damaged by
e
l
e
ctrostatic discharge. Keep parts in their
c
ontainers until needed. Ensure you are
properly grounded when touching static-
2
s
e
n
sitive components.
i
br
a
ry off-line by pressing the
P
o
w
er down the library.
a
. Place the l
S
t
a
ndby button on the library's front panel.
T
h
e library robotics completes any current
c
ommands and then stops.
b
.
Verify that the front panel display indicates
“System Off-line”.
c
. Verify that the picker is empty. If there is a
2
1
t
ap
e cartridge in the picker, perform a Move
c
o
mmand to place the cartridge in an
a
vailable slot. [Content needed.]
d
.
P
ress and hold the power button located on
U
t
h
e
front of the library behind the laptop tray
When the power is on, the ACT/LNK LEDs wil
u
n
t
i
l the front panel goes blank.
4
be off instead of green; the power LED might also
I
n
s
p
ect the contents of the kit.
be off. You may need to find out which drives are
3
F
l
i
p
the two breaker switches off at the power
connected to each interface controller to identify
d
i
s
t
ribution unit.
t
he controller to be replaced.
O
p
en the back door of the library.
To power off the library,
a. Stop all library activity and ensure that the
picker is empty.
door at the rear of the rack.
b. Open the
c. Set the rack power switch at the upper right
corner to the OFF position.
d. Ensure that all power indicators on the power
supplies are off.
Inspect the contents of the kit. You will need a
flat-blade screwdriver to remove and replace this
tape drive.
Ethernet
cable
Serial
cable
If you are replacing an interface controller, locate
the original card in the second card cage slot in
the base module or in one of the slots in the card
Inspect the contents of the kit.
cage expansion module. This card contains two
NOTE: There are two different kits. A new
HBA or switch FC ports, four tape drive FC ports,
installation kit will contain:
one Ethernet port, and one serial port. You may
1) installation poster, 2) interface controller,
need to find out which drives are connected to
3) Ethernet cable, 4) serial cable.
each interface controller to identify the controller
A replacement kit will contain:
to be replaced. You will need a #1 Phillips
1) installation poster, 2) interface controller.
screwdriver to remove and replace this card.
...Otros modelos de este manual:
datos de dispositivos de procesamiento - HP EML 103e Tape Library (1.02 mb)
datos de dispositivos de procesamiento - HP EML 245e Tape Library (1.02 mb)
datos de dispositivos de procesamiento - HP EML Base Library (1.02 mb)
datos de dispositivos de procesamiento - HP EML E-Series 103e Base Tape Library (1.02 mb)