Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
the ejection handles to the inside to fully seat the card. Tighten the
a. To determine the IP address to use, look at the OCP on the
captive screws.
front of the library. From the Home screen, select the Status
tab, and then select Identity Screen.
b. On the host PC or laptop, open a command shell and navigate
Reconnect the cables
to the directory where the firmware you downloaded in Step
1 is located.
CASCADE
TO FIBRE CHANNEL CONTROLLERS
NETWORK
SERIAL
AUX
STATUS
c. Enter the following command: ftp IPaddress
nl
ERROR
where IPaddress is the IP address from the OCP.
d. Login with the fol owing credentials:
User name: ftp
Password: Use your e-mail address
e. Enter binary mode with the command: bin
f. If necessary, use the ls command to list the contents of the
FTP directory.
11799
Plug the cables into the Interface Manager card exactly as they were
g. Enter the following command to copy the firmware file to the
plugged into the original card.
temporary location in the Interface Manager card’s memory:
nl
put filename
nl
where filename is the filename of the firmware file.
Power on the library
h. Use the quit command to log off the FTP session.
Set the library power switch at the upper right corner to the ON position.
3. Start a Telnet session on the PC or laptop:
Check the power supply power indicators to verify that the power is on.
a. From a command prompt, enter the following:
nl
Verify that the library robotics controller Active indicator is lit. The library
telnet
nl
IPaddress
will take 20 minutes or more to boot, depending on the configuration.
where IPaddress is the IP address from the OCP.
b. At the login prompt, enter the following information:
Username:
Verify the library status
admin
Password: admin
4. Enter the following command to update the firmware:
nl
download mgmt
5. Start a Telnet connection. (The Telnet connection will have been
CASCADE
TO FIBRE CHANNEL CONTROLLERS
NETWORK
SERIAL
AUX
STATUS
lost during the firmware update.)
ERROR
6. Enter the fol owing command to verify that the firmware was
10557
updated correctly: show mgmt revision
Look at the status LEDs on the Interface Manager card. The red LED
7. Enter the following command to set the system date and time:
should be off and the green LED should be blinking or solid.
nl
set mgmt clock MMDDhhmmyy
w
nl
here:
Configure the network
MM
nl
is the month
DD
nl
is the date
Do one of the following depending on whether the Interface Manager
hh
nl
is the hour in 24-hour format
card’s IP address is dynamic or static:
mm
nl
is the minute
yy is the last two digits of the year
• If the IP address is dynamic, go to the next step.
8. Log off the Telnet connection and disconnect the host PC or laptop
• If the IP address is static, use the OCP to configure the IP address,
from the LAN.
using the information you determined in Determine the IP address
configuration.
To update the firmware with the GUI:
Update the firmware
1. If you do not already have the latest version of the Command View
TL software, install it by following the instructions in “Installing
Command View TL” in the HP StorageWorks Interface Manager
After replacing the CompactFlash card, you must update the Interface
and Command View TL user guide.
Manager card firmware and reconfigure the Interface Manager card
set ings. You can update the firmware with either the CLI or the GUI.
2. To start Command View TL, click Start > All Programs > HP
Command View TL > Command View TL.
To update the firmware with the CLI:
1. Using a PC or laptop connected to the LAN, download the latest
fi
nl
rmware from the web site:
ht p://www.hp.com/support/cvtl
2. Use FTP to transfer the firmware file to a temporary storage area
in the Interface Manager card’s memory.
Page 3
...Otros modelos de este manual:
datos de dispositivos de procesamiento - HP EML 245e Tape Library (688.17 kb)
datos de dispositivos de procesamiento - HP EML Base Library (688.17 kb)
datos de dispositivos de procesamiento - HP EML E-Series 103e Base Tape Library (688.17 kb)
datos de dispositivos de procesamiento - HP EML71e LTO-4 Ultrium 1840 Tape Library (688.17 kb)