Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
EML E-Series
HP
Library
StorageWorks
Robotics
Controller
Caution: Parts can be damaged by
Note: This part is not hot-pluggable.
electrostatic discharge. Keep parts in their
It is necessary to power down the library
containers until needed. Ensure that you
to replace this part.
are properly grounded when touching
static sensitive components.
1
2
ESL
E-Series
Robotics
HP
Controller Card
)
StorageWorks
Note: This part is not hot-pluggable.
Power off the library.
I
t is necessary to power down the library
to replace this part.
Caution: Parts can be damaged by
electrostatic discharge. Keep parts in their
en touching
containers until needed. Ensure that you
are properly grounded
static sensitive components.
a. Stop all library activity
2
1
Power off the library.
and ensure that the
a. Stop all library activity and ensure that the
picker is empty.
E
S
L
E
-
s
eries
b. Open the door at the rear of the rack.
I
n
t
erface
M
anager
h
p
1
0
0
2
6
N
o
te: This part is not hot-pluggable.
I
t
i
s
necessary to power down the library
S
t
o
rageWorks
t
o
r
eplace this part.
c. Set the rack power switch at the upper right
C
a
ution: Parts can be damaged by
e
le
ctrostatic discharge. Keep parts in their
c
ontainers until needed. Ensure you are
corner to the OFF position.
p
r
operly grounded when touching static-
2
s
e
n
sitive components.
P
o
w
er down the library.
a
. Place the library off-line by pressing the
S
t
a
ndby button on the library's front panel.
T
h
e library robotics completes any current
c
ommands and then stops.
b
.
Verify that the front panel display indicates
“System Off-line”.
1
c
.
V
erify that the picker is empty. If there is a
d. Ensure that al power indicators on the power
picker is empty.
t
a
p
e cartridge in the picker, perform a Move
c
o
mmand to place the cartridge in an
a
vailable slot. [Content needed.]
d
.
Press and hold the power button located on
t
h
e
front of the library behind the laptop tray
u
n
t
i
l the front panel goes blank.
supplies are off.
4
I
n
s
p
ect the contents of the kit.
3
Fl
i
p
the two breaker switches off at the power
d
i
s
tribution unit.
O
p
en the back door of the library.
I
nspect the contents of the kit.
Removal
b. Open the doors at
4
Public
CLI port
Ethernet port
Reserved
(
connect to
(
RS-232 –
ace
port
)
not used
r
Private
(
not used)
Ethernet port
Card)
3
(not used)
the rear of the rack.
rnet
Remove all cabling to the library robotics
Locate the card in the top card cage slot in the
control er card while noting cable locations for
c. Set the rack
base module. This card contains one Ethe
nects to the Interface Manager
l
ater reconnection.
connection that con
card. The function of this card is to control the
robot. You wil need a #1 Phillips screwdriver to
remove and replace this card.
power switch at
the upper right corner
Inspect the contents of the kit.
to the OFF position.
Removal
3
4
Public
Ethernet port
(connect to
Private
Interface
Reserved
CLI port
Ethernet port
Manager
port
(RS-232 –
(not used)
Card)
(not used)
not used)
Locate the card in the base module. You will
Remove the Ethernet cable from the Public Ethernet
need a #1 Phillips screwdriver to remove and
port on the library robotics controller noting the
replace this card.
cable location for later reconnection.
...Otros modelos de este manual:
datos de dispositivos de procesamiento - HP EML 245e Tape Library (1.09 mb)
datos de dispositivos de procesamiento - HP EML Base Library (1.09 mb)
datos de dispositivos de procesamiento - HP EML E-Series 103e Base Tape Library (1.09 mb)
datos de dispositivos de procesamiento - HP EML71e LTO-4 Ultrium 1840 Tape Library (1.09 mb)