11 Remove the screws from the drive
13 Plug the cables into the switch
clusters
If you are replacing the switch, skip this step because the screws wil
already be removed.
11609
11590
Keep the screws to use for at aching the switch to the cabinet.
NOTE:
If an LTO4 tape drive is not installed, fol ow the instructions on
the tape drive installation poster to instal it.
12 Insert the switch into the cabinet and
attach it with the screws
If the switch was previously installed, use the labels on the cables or
the note that you wrote to reconnect the cables exactly as they were
connected before. If you are installing the switch for the first time, plug
an Ethernet cable from the MGMT port on each LTO4 tape drive to a
numbered port on the switch. HP recommends that you connect the
tape drives to the switch in order starting with cluster 1, tape drive A
connecting to port 1. If you have 24 tape drives, connect tape drive
24 to port E4 on the cluster controller (left card in the drive cluster) in
the bottom drive cluster (port 24 is used in the next step). LTO3 tape
drives do not plug into this switch.
14 Connect the switch to a cluster
controller
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
EL
N
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
SERIAL
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
R
PW
NET
THER
E
0

T
POR
1
T
R
PO
2
T
POR
3
T
R
O
P
1
T
R
PO
2
T
POR
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
EL
N
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
SERIAL
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
R
PW
NET
THER
E
0

T
POR
1
T
R
PO
2
T
POR
3
T
R
O
P
1
T
R
PO
2
T
POR
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
EL
N
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
SERIAL
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
R
PW
NET
THER
E
0

T
POR
1
T
R
PO
2
T
POR
3
T
R
O
P
1
T
R
PO
2
T
POR
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
EL
N
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
SERIAL
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
R
PW
NET
THER
E
0

T
POR
1
T
R
PO
2
T
POR
3
T
R
O
P
1
T
R
PO
2
T
POR
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
EL
N
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
SERIAL
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
R
PW
NET
THER
E
0

T
POR
1
T
R
PO
2
T
POR
3
T
R
O
P
1
T
R
PO
2
T
POR
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
EL
N
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
SERIAL
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
R
PW
NET
THER
E
0

T
POR
1
T
R
PO
2
T
POR
3
T
R
O
P
1
T
R
PO
2
T
POR
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
LNK
EL
N
CHAN
LNK
NEL
CHAN
LNK
NEL
CHAN
SERIAL
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
ACT/
FIBRE
R
PW
NET
THER
E
0

T
POR
1
T
R
PO
2
T
POR
3
T
R
O
P
1
T
R
PO
2
T
POR
11587
Route the power cable so it will reach the PDU. Use a #2 Phillips
11649
screwdriver to tighten the screws.
Connect an Ethernet cable from port 24 on the switch to any unused E#
port on any of the cluster controllers (left card in the drive cluster).
Page 4

---

...

Otros modelos de este manual:
datos de dispositivos de procesamiento - HP ESL 712e Ultrium Tape Library (1.11 mb)
datos de dispositivos de procesamiento - HP StorageWorks ESL 286e 286 Slot SDLT Library (1.11 mb)
datos de dispositivos de procesamiento - HP StorageWorks ESL 286e SDLT Tape Library (1.11 mb)
datos de dispositivos de procesamiento - HP StorageWorks ESL 322e 322 Slot Ultrium Library (1.11 mb)