Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Read all instructions. 2. Use iron only for its intended use. 3. To protect against a risk of electric shock, other liquids. 4. The Iron should always be turned to “min” position from outlet. Never yank cord to disconnect from pull to disconnect. 5. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. 6. Always disconnect iron from electrical outlet when filling with water and when not in use. 7. Do not operate iron with a damaged cord or if the Iron has been dropped damaged. To avoid the risk of electric shock, do not disassemble the Iron. Incorrect reassembly can cause a risk of electric shock when the Iron is used. Contact Consumer Service for examination and repair. 8. Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board. 9. Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down -- there may be hot water in the Water Tank. SPECIAL INSTRUCTIONS 1. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. SAVE THESE INSTRUCTIONS For Household Use Only 1 ADDITIONAL SAFEGUARDS CAUTION HOT SURFACES: This appliance use. Proper precautions injury to persons or damage to 1. All users of this appliance must Manual before operating or cleaning this appliance. 2. The cord to this appliance should be plugged 3. If this appliance begins to malfunction during not use or attempt to repair the malfunctioning 4. Do not leave this appliance unattended during use. Polarized Plug This appliance has a polarized plug (one blade is wider than the reduce the risk of electric shock, this plug is intended to fit into a polarized outlet If the plug does not fit fully in the outlet, reverse the plug. If it still does qualified electrician. Do not attempt to modify the plug in any way. Electric Power If the electrical circuit is overloaded with other appliances, your appliance may not operate properly. It should be operated on a separate electrical circuit from other appliances. Electrical Specifications 120V ~ 60Hz 1400W Auto Shut-Off For added safety, the Iron will shut off automatically when either of the following instances occurs: • The Iron is left standing in the vertical position (on its Heel Rest) for more than 15 minutes. • The Iron is left in the horizontal position (on its Soleplate) for more than 30 seconds. When the Iron switches into Auto Shut-Off mode, the green Auto Shut-Off Light will illuminate and will flash until the Iron is moved or unplugged. 2 Getting Know Your Westinghouse Thermocolor ™ Steam Iron Product may vary slightly from illustrations. 1. Spray Nozzle 2. Water Fill Opening 3. Blast of Steam Button 4. Spray Button 5. Steam Control Dial 6. Pivot Cord 7. Auto Shut-Off Light (green) 8. Thermostat Light FIGURE 1 Level Line 14. Steam Vents 15. Filler Cup (P/N 50759) X 1 2 NO STEAM LOW HIGH Self-Clean FIGURE 3: Steam Control Dial (red) 9. Heel Rest 10. Water Tank 11. Temperature Control Dial 12. Ceramic Soleplate 13. Maximum Water FIGURE 2: Temperature Control Dial 3 Thermocolor ™ Technology: As the temperature changes… So does the color! This Iron features a lighted Tank that glows in different when the desired temperature temperature setting has been Tank will cycle through the colors, indicating changes in actual ironing When the Iron is first plugged in, the Tank glows blue, the lowest heat setting. The color-coded Temperature Control Dial shows the progression heats from blue to green, then to lilac, and Fabric/Temperature Setting Guide FABRIC TEMPERATURE COLOR Delicate, Silk min Blue Nylon, Acrylics, Polyester • Blue Wool, Polyester blends • • Green Cotton, Linen • • • Lilac Cotton, Linen max Red FIGURE 4 Ironing Tips • For best results, check garment labels for the temperature and steam setting recommended by the fabric manufacturer. • If you are unsure of a garment’s fabric content, start on a low setting and test the Iron on an area of the garment that does not show, such as a seam. Gradually increase the heat setting until wrinkles remove without damaging the fabric. • To freshen up garments made of velvet, felt, suede or velour, hold the steaming Iron horizontally 2 inches (5 cm) above the fabric for a gentle steaming. Make sure the Iron does not come in contact with the fabric. • To prevent shine, iron dark garments or those made of silk, acetate or rayon inside out. • For quick and easy reference, a condensed fabric guide is imprinted on the Heel Rest of the Iron (see illustration below). 4 OPERATING INSTRUCTIONS Before First Use 1. Remove all packaging materials Iron. Unwind and straighten the 2. Flush the Steam Ve...
Otros modelos de este manual:Planchas - WST5017 (687.08 kb)