Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
the Iron back in the vertical position (on its Heel completely before cleaning or storing. NOTE: The Water Tank should be emptied after each use. Blast of Steam The Blast of Steam Button releases a penetrating blast of steam wrinkles and to iron faster. 1. When using the Blast of Steam feature, the Temperature Control Dial must be positioned to at least the “ ” symbol -- located midway between the GREEN (• •) and LILAC (• • •) settings. For best results, use the “max” (RED) temperature and keep the Water Tank at least half full. Blast of Steam Button 2. Firmly press the Blast of Steam Button once, then release (see FIGURE 7). It may be necessary to press the Blast of Steam Button 2 -3 times successively to release the initial burst. DO NOT HOLD THE BLAST OF STEAM BUTTON DOWN. CAUTION: AVOID COMING IN CONTACT WITH ESCAPING STEAM. 3. As the Blast of Steam Button is pressed and steam is FIGURE 7 released, the temperature of the Iron drops; thus the Water Tank color may cycle down momentarily. Allow at least 4 seconds between Blasts of Steam to allow the Iron to regain heat. NOTE: The red Thermostat Light will continue to cycle off and on during use as the Iron maintains the desired temperature. 7 Vertical Steam The Blast of Steam from clothes while on and to freshen the appearance or drapes. 1. When steaming drapes or curtains ventilation behind the fabric to prevent Always make sure there is nothing behind the Before steaming clothes, check that pockets, 2. Make sure that the Temperature Control Dial is set to the “max” before releasing vertical blasts of steam. For maximum Tank at least half full. CAUTION: IF THE IRON IS HOT, DO NOT FILL WITH WATER. 3. Hold the Iron upright so that the Soleplate is 7-15 inches (18-38 cm) away from the garment or material. Press the Blast of Steam Button once, then release (see FIGURE 8). It may be necessary to press the Blast of Steam Button 2- 3 times successively to release the initial burst. DO NOT HOLD THE BLAST OF STEAM BUTTON DOWN. CAUTION: AVOID COMING IN CONTACT WITH ESCAPING STEAM. FIGURE 8 Blast of Steam Button 4. As the Blast of Steam Button is pressed and steam is released, the temperature of the Iron drops; thus the Water Tank color may cycle down momentarily. Allow at least 4 seconds between blasts of steam to allow the Iron to regain heat. NOTE: The red Thermostat Light will continue to cycle off and on during use as the Iron maintains the desired temperature. Spray Button Spray Nozzle FIGURE 9Spray Button Use the Spray Button for moistening dry, difficult fabrics, and for handling stubborn wrinkles. The Spray function is also handy to moisten creases accidentally ironed into the fabric. 1. Make sure there is water in the Water Tank (see FILLING THE WATER TANK for detailed instructions) . CAUTION: IF THE IRON IS HOT, DO NOT FILL WITH WATER. 2. Aim the Spray Nozzle at the desired target, and then firmly press the Spray Button (see FIGURE 9). It may be necessary to press the Spray Button 2-3 times successively to release the initial spray of water. NOTE: The Spray function can be used on any heat setting and does not affect the ironing temperature. 8 USER MAINTENANCE This appliance requires parts. Do not try to repair it yourself. Any requiring disassembly by a qualified appliance repair Emptying the Water Tank The Water Tank should be emptied after each use. 1. When finished ironing, turn the Temperature Control Dial to the “min” position; turn the Steam Control Dial to steam) position, and unplug the Iron. 2. While the Iron is still warm, hold it over a sink and turn down, allowing water to drain from the Water Fill Opening (see FIGURE 10) . 3. Turn the Iron back to the horizontal position. Press the Blast of Steam and Spray Buttons to release any water (see FIGURE 11) . The warmth of the Iron should dry out any remaining water. CAUTION: AVOID COMING IN CONTACT WITH WATER OR ESCAPING STEAM. Care and Cleaning FIGURE 10 FIGURE 11 CAUTION: Unplug the Iron from the electrical outlet and allow it to cool completely before cleaning and storing. Never immerse the Iron in water or any other liquid. NOTE: Do not put any chemical cleaning agents or solvents in the Water Tank, or on any part of the Iron. 1. Moisten a soft cloth with a dab of vinegar to remove spots from the Ceramic Soleplate. Take care not to scratch the Soleplate. CAUTION: Never use scouring pads or abrasive cleaners on the Ceramic Soleplate, as this may scratch the surface. 2. Wipe the outside surfaces of the Iron with a damp cloth. If necessary, use a small amount of mild detergent to clean. 3. Before using again, preheat and move the iron over an old cloth several times to remove any residue from the Ceramic Soleplate. Self-Clean Function It is advised to use the Self-Clean function after every 5 uses to prevent harmful mineral build-up that can clog the Iron and prevent proper heating and steaming. 1. With the Iron unplugged, turn the Temperature Control Dial to the “min” position and the Steam Cont...
Otros modelos de este manual:Planchas - WST5017 (687.08 kb)