Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Please make sure the water reservoir is 1/4 full of water. TIP: Refer to the Ironing Guide for the recommended setting for your fabric. STEAM IRONING 1. Follow the instructions for “Filling the Water Reservoir”. 2. Plug the cord into a 120-Volt AC outlet. 3. Turn the Fabric Select Dial to the fabric setting you desire. Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface. 4. Allow the iron to heat for 2 minutes, and then turn the Steam lever to the appropriate setting. TIP: Refer to the Ironing Guide for the recommended setting for your fabric. IMPORTANT: When not ironing, always set the Steam Lever to /Off (Dry) and the Fabric Select Dial to OFF. USING THE IRON’S SPECIAL FEATURES SPRAY MIST® FEATURE The SPRAY MIST® feature is a powerful water spray mist that dampens the fabric to aid in removing wrinkles from heavy fabrics and for setting creases. To use the SPRAY MIST® Feature: Press the SPRAY MIST® button firmly. SHOT OF STEAM® FEATURE To use the SHOT OF STEAM® Feature: Place the iron on top of the wrinkle and press the SHOT OF STEAM® button each time you would like an extra burst of steam. The SHOT OF STEAM® feature may be used continuously in approximately 3 second intervals. VERTICAL STEAM (select models only) The vertical steam feature allows your iron to function as a garment steamer. TIP: When using the vertical steam on clothing, hang the clothing on a clothes hanger for best results. Hanging curtains and drapes may also be steamed. To use Vertical Steam: 1. Make sure that the iron has heated up (2 minutes). 2. Hold the iron in a vertical position, with the iron close to but not touching the fabric you want to steam. 3. With your other hand, pull the fabric tight. 4. Press the SHOT OF STEAM® button for approximately 3-second intervals as you move the iron across the wrinkled area. WARNING: To prevent the risk of burns, keep your hand away from the area being steamed. WARNING: DO NOT steam garments while wearing them; this may result in injuries. CLEANING THE ANTI-CALCIUM SYSTEM (select models only) The Simple Press™ iron houses an anti-calcium filter in the reservoir, which eliminates impurities from the water. To prolong the efficiency of this filter: 1. Unplug the iron and allow it to cool. 2. Locate the water cup that accompanied the iron. Fill it with water to the Sunbeam logo in the top right corner. Add 1 teaspoon of salt to the water and fill the water reservoir with this solution. 3. Leave the solution in the water reservoir for 15 minutes, shaking occasionally, and then empty it. 4. Fill the water reservoir a second time with the salt water solution, shaking occasionally, and empty it again after 15 minutes. 5. Fill the tank with fresh water to rinse and empty. The Anti-Calcium System should be cleaned approximately once a month. MOTION SMART® AUTO-OFF FEATURE When the iron is plugged in, the Power Indicator will light steadily, indicating that there is power to the iron. If you leave the iron: • in a horizontal position without moving it, or accidentally tip the iron over, it will automatically stop heating after 30 seconds. The Power Indicator will blink to let you know that the iron has stopped heating. CARACTERISTIQUES DU FER SIMPLE PRESS™ 1. Orifice d’atomisation SPRAY MIST® 2. Orifice de remplissage a volet 3. Cadran de selection des textiles 4. Levier de vapeur 5. Bouton d’atomisation SPRAY MIST® 6. Bouton du jet de vapeur SHOT OF STEAM® / Vapeur verticale (certains modeles seul) 7. Temoin marche-arret MOTION SMART® 8. Cordon articule 360° non emmelant 9. Bouton d’autonettoyage 10. Reservoir translucide 11. Semelle 12. Indicateur Storage Strip™ 13. Systeme anti-tartre (certains modeles seul) or facing, before ironing a visible area. Start with a low temperature and gradually increase the heat to find the best setting. • When changing the temperature from a high setting to a low setting, allow approximately 5 minutes for the lower temperature to be reached. • When steam ironing, use long, slow passes over the fabric. This will allow the steam to penetrate the fabric while allowing the heat of the soleplate to dry out the moisture. • To iron linens, turn garment inside out. Be careful not to use an iron that is too hot because the lining may melt or stick to the soleplate. • To iron zippers, use an ironing cloth or make sure the zipper is closed and iron over the flap. Never iron directly over an unprotected zipper. • Use the Ironing Guide to select the best setting and method for the fabric you plan to iron. • SUNBEAM® irons are designed to be used with ordinary tap water. In areas where hard water exists, Sunbeam recommends running one to two iron water tanks full of distilled water every month. Using distilled water on a monthly basis will help to prevent mineral build up. CAUTION: Do not overuse distilled water. It may cause the iron to drip or spit if it is used too often. REMPLISSAGE DU RESERVOI...
Otros modelos de este manual:Planchas - 3051 (188.62 kb)
Planchas - 3061 (188.62 kb)
Planchas - 3062 (188.62 kb)