Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
• Do not immerse the appliance in water or any other liquid unless recommended. If you have any concerns regarding the performance and use of your appliance, please visit or contact the Sunbeam Consumer Service Line. Ensure the above safety precautions are understood. Features of your Ultura Dry Iron LongcordwithswivelcordoutletTheswivelcordoutletisidealforleftorrighthanduse,andprovidesgreaterversatilityandeaseofmovementwhenironing.Theflexiblegrommetprotectsthecordfromfraying. TemperatureindicatorAlignthedesiredsettingwiththetemperatureindicator. ................................................................................................ ThermostatlightIlluminatestoindicatethattheironisheatingandgoesoutwhenithasreachedthetemperatureselectedonthetemperaturedial.Thethermostatlightcyclesonandoffduringironingastheironmaintainstheselectedtemperature. TemperaturedialAllowsyoutoselectthedesiredtemperatureforeachgarment. StableheelrestLargeheelrestkeepstheironstableontheironingboard. Figure 1FulllengthbuttongrooveForironingaroundbuttons. Teflon®PlatinumPronon-sticksoleplateGlideseasilyacrossalltypesoffabricandpreventssticking. CordwrapfacilityThebuilt-incordwrapfacilityallowsyoutowindthecordaroundtheheelforneatandtidystorageofthecordwhentheironisnotinuse. Using your Ultura Dry Iron Before first use Remove any adhesive stickers, plastic covers or cardboard sleeves from the soleplate. Ensure that all adhesive is removed by rubbing the soleplate with a cloth dampened with methylated spirits. NOTE: When turned on for the first time, your new iron may give off vapours for up to 10 minutes. This is due to the initial heating of the materials used. It is safe, not detrimental to the performance of the iron, and will not reoccur. Using your iron 1.Insert the 3 pin plug into a 230/240 volt power outlet and turn the power on. 2.Turn the temperature dial to the desired setting by aligning the setting on the dial with the temperature indicator. The thermostat light will illuminate to indicate that the iron is heating to the selected temperature. When the thermostat light goes out the iron is at the selected temperature and is ready to iron. NOTE: When the temperature dial is changed from a high setting to a lower temperature setting during ironing, the thermostat light will go out immediately. This indicates that the iron is cooling to the selected temperature. To ensure that the iron has reached the selected temperature and is not too hot, wait until the thermostat light comes on again and then goes out before ironing. Care and Cleaning After each use 1.Turn the power off and remove the plug from the power outlet. 2.Allow the iron to cool before winding the cord around the built-in cord wrap. Storage Always store the iron on its heel rest. NOTE: Do not store the iron with the soleplate facing down, or in the carton. Cleaning To clean the exterior of your iron, wipe over with a damp soft cloth and wipe dry. Caution: Do not use harsh abrasives, chemical cleaners or solvents to clean the exterior of your iron as these will damage the surface. Cleaning the Teflon® Platinum Pro non-stick soleplate The non-stick coating reduces sticking of fabrics and starches to the soleplate. Do not iron over sharp objects such as buttons, studs and zippers, as these will scratch the surface. Wipe the soleplate with a damp soft cloth after each use. If polyester has burnt to the soleplate, iron a damp cotton cloth while hot. Caution: Do not use scouring pads, abrasives or harsh cleaners to clean your Teflon® Platinum Pro soleplate, as these will scratch and damage the surface. Ironing Guide Selecting ironing temperature Always read garment labels and follow the manufacturer’s ironing instructions. Hints for easier ironing • Sort articles to be ironed according to the type of fabric. This will reduce the need to adjust the temperature to suit varying garments. • Start with garments requiring lower temperatures and work your way through to items requiring higher temperatures. • If you are unsure of the fabric content of a garment, test a small area such as a seam or inside hem section before ironing a visible area. Start with a low temperature and gradually increase the heat to find the best setting for ironing the garment. • When reducing the temperature to iron sensitive fabrics, allow approximately 2 minutes for the iron to cool to the new setting. • Pure woollen fabrics (100% wool) can be ironed with the temperature dial set to Wool. Use an ironing cloth to prevent shine marks on the fabric. • Fabrics such as velour, wool, linen and silk are best ironed with an ironing cloth to prevent shine marks. • Never iron areas of a garment where perspiration marks are visible, as the heat of the iron will fix the stains, making them permanent. ‘Sunbeam’, and ‘Ultura’ are registered trademarks of Sunbeam Corporation. Made in China to Sunbeam's specification. Due to minor changes in design or otherwise, the product may differ from th...