Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
To turn iron off, set Adjustable Steam Switch to Dry Iron O. Turn the Temperature Control Dial to OFF ( O ). Unplug iron. 8. Empty water from the iron following directions in “Caring for Your Iron.” Water Please use ordinary tap water. If you have extremely hard water, alternate between tap water and distilled water for use in the iron. FABRIC SETTING CHART Steam Setting Temperature Setting Ironing Instructions Dry IronO Off Nylon, Acrylic Silk Polyester • • •• Dry iron using spray if necessary. Dry iron on the wrong side of the fabric. Iron while fabric is still damp. Steam Range Wool Rayon Cotton, Linen •• ••• ••• Use a press cloth and steam iron on the wrong side of fabric. Iron using spray if necessary. For cotton, iron while still damp or use spray. For linen, iron fabric on wrong side. 4 840165700 Ev02 5/1/07 4:05 PM Page 5 CARING FOR YOUR IRON Iron 1. The water tank of your iron should be emptied after each use. Turn Temperature Control Dial to OFF ( O ). Unplug the iron and hold over a sink. Slowly tilt pointed end of iron down over sink. Water will run out of water tank opening. 2. After iron has completely cooled, fully retract cord into iron or loop cord loosely around iron, as applicable, and store in an upright position. NOTICE: Do not store iron laying flat on soleplate. Soleplate 1. Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the soleplate. 2. To clean occasional build-up on the soleplate, wipe with a sudsy cloth. Do not use abrasive cleansers or metal scouring pads. 3. Always store iron upright in the heel rest position. Self-Clean (on selected models) To keep the steam vents clear of any build-up, follow these instructions each time you iron using steam. 1. Turn Temperature Control Dial to OFF ( O ) and set Adjustable Steam Switch to Dry Iron O. Fill iron with water to 1.2 of its maximum capacity. 2. Turn Temperature Control Dial to Linen setting and let iron heat for 2 minutes. Keep Adjustable Steam Switch on Dry Iron O. 3. Turn Temperature Control Dial to OFF ( O ). Unplug iron and hold over a sink with soleplate facing down. 4. Turn Adjustable Steam Switch to MAX, while pressing Blast of Steam button often. Boiling water and steam will flow out of steam vents. Allow all water to drain from iron. 5. Gently move iron front to back to allow water to clean entire soleplate area. 6. If water still remains inside of soleplate, reheat iron as indicated in Step 2. Boiling water and steam could still flow out of steam vents. 5 840165700 Ev02 5/1/07 4:05 PM Page 6 FEATURES (on selected models) Adjustable Steam Switch This knob provides steam for fabrics such as wool and linen. See the “Fabric Setting Chart” for details. Set the switch to Dry Iron O to iron without steam. Spray and Blast of Steam Buttons Push Blast Button for an extra blast of steam. Push Spray Button to release a fine spray of water for difficult wrinkles in cotton or linen. Power ON/ Auto Shutoff Reset Button/Light This light comes on when the iron is first plugged in. After one hour, the iron will shut off and the light will go out. Push the Reset Button/Light to turn the iron back on. Power On Light On units not provided with Auto Shutoff, this light comes on when the iron is plugged in and remains on until the iron is unplugged. The light stays on even if Temperature Control Dial is turned to OFF ( O ). Retractable Cord 1. Pull cord to desired length. Do not unwind cord beyond colored tape indicator on cord. 2. To store cord, press and hold the Cord Release Button while guiding the cord into the storage area. w wwWARNING: To reduce the risk of an eye injury, hold the plug while retracting the cord. 6 840165700 Ev02 5/1/07 4:05 PM Page 7 TROUBLESHOOTING PROBLEM Things TO CHECK Iron won’t heat. • Is the iron plugged in and the outlet working? Check the outlet by plugging in a lamp. • Is the Temperature Control Dial turned to a fabric setting? • If auto shutoff model, is the Reset Light illuminated? If not, push to reset. Water is leaking • Do not overfill the water tank. out of the iron. • If steam ironing, is Adjustable Steam Switch in a steam position and the Temperature Control Dial in the steam range? Did the iron have enough time to preheat? • If dry ironing, make sure the Adjustable Steam Switch is in the DRY IRON position. Iron won’t steam. • Check the water level. • Is the Adjustable Steam Switch in the STEAM position? • Has the iron had enough time to preheat? Iron leaves spots • ALWAYS empty the water tank of the iron after using. on clothing. Water left in the tank may discolor clothing and soleplate. Wrinkles not • Check Temperature Control Dial is set to correct fabric. removed. Fabric/clothing • Check Temperature Control Dial and set to lower setting. scorched. Allow iron to cool down 5 minutes before continuing. Twisted cord. • If the iron cord should become twisted, turn iron OFF (O), turn Control Dial to OFF (O) and unplug iron. Let cool. Empty water from iron.Hold iron cord in th...
Otros modelos de este manual:Planchas - 169159 (211.35 kb)