Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
To start and stop/ pause the ironing airing processes. 4.-programme selector switch. To select the ironing and/or airing programme. 5.-Digital screen. Shirt ironer, Fig. 2 6.-Head section unlocking clip. 7.-Collar adjuster knob. 8.-Button band adjuster. 9.-Control panel. 10.-Transportation handle. 11.-Upper head section. 12.-Collar adjuster. 13.-Collar support. 14.-Inflatable ironing dummy. 15.-Cuff adjuster. 16.-Size adjustment cords. 17.-Cable compartment. 18.-Characteristics plate. 19.-Filter cover and air filter. 20.-Wheels. Before using your shirt ironer Your shirt ironer is supplied fully assembled and packed to protect it during transportation. There is a rubber tightener stitched onto the cover appliance which fits onto a guide on the shirt ironer to hold the cover appliance in place. o Remove the cover appliance. o Cover the shirt ironer with the cover appliance when not in use. Installing your shirt ironer Warning! The shirt ironer must be fully lowered for transportation! The shirt ironer is fitted with two wheels. There is a handle on the front 10, Fig. 2 of the appliance to help move it more easily. Tilt the shirt ironer by lifting the handle on the front and wheel it to the desired work location. Work area The work area needs to measure approximately 2.50 m x 1.00 m. Setting up your shirt ironer The cable is rolled up on the cable supports on the back of the shirt ironer, 17, Fig. 2. Unroll the required length of cable and plug it in. Selecting the connection current The Ironer can work at 10 or 16 Amps depending on the power of the mains electricity supply available. The appliance is supplied in the 16-Amp version (see characteristics plate, 19, Fig. 2). If you wish to use the Shirt ironer at 10A, then you need to change the connection current as follows: 6 Before using your shirt ironer Adjusting the connection current: Adjusting the indicator light The appliance is plugged in. The shirt ironer is off and the programme selector switch 4, Fig. 1, is set to “0”. The button band is fully lifted. o Press the and the start/stop buttons in at the same time and keep them pressed in. o Three sound signals are emitted to confirm the operation. o Digital screen 5, Fig. 1, displays the current the appliance is set to. o Press “Start/stop“. The screen displays the connection current setting. Press the same button again to change the current. o Three sound signals are emitted to confirm the operation. o Press when the current you wish to work at is displayed on the screen; the shirt ironer switches itself off and the new setting is stored in the memory. o The ironing time is longer with the 10-Amp setting. o The 16-Amp setting is recommended for enhanced performance. Adjusting the signal Sound signals are emitted to indicate that a specific circumstance has taken place in the programme. o Change in the connection current setting. o End of ironing and airing cycle. o The light flashes 10 times when the appliance is already at its lifted position when plugged in. o The light flashes 10 times when the appliance is lifted from its down position when already plugged in. The light flashes to remind you to press the button at the start of use in order to initiate preheating and thereby reduce shirt drying time. o The light lights up when the appliance is working. o The start / stop light and the light light up when the appliance is blowing air, in any cycle. o When the appliance is on pause, the start / stop light flashes for the 30 seconds that this function lasts. Adjusting the size The size of the ironing dummy is based on European shirt sizes. The size can be adjusted between sizes 35 and 50. These sizes coincide with American sizes XS and 4XL. In the case of blouses, sizes 36/38 to 50/52 (S to XXL) can be used. The ironing dummy can be adapted to different cuts (e.g. tapering, blouse cuts) by adjusting the size. This is done by adjusting the 3 adjustment cords 16, Fig. 2. To adjust the size, start by adjusting the top cord. The volume of the ironing dummy cannot be reduced when inflated. 2 button arm straps are supplied for ironing short-sleeved shirts, Fig. 3. 7 Before using your shirt ironer Preparing your garments The appliance is only intended for ironing shirts and blouses made with non-elasticated fabric. Garments must be spin-dried prior to ironing. Warning! Do not iron knitwear or garments made with elasticated fabric! They may loose shape. Ironing In order to get the best results from ironing: o Spin dry the garment at 800 revolutions/minute after washing. o Shirts and blouses can be spin-dried at lower speeds if your washing-machine does not have an 800 revolution/minute spin-dry programme. Ironing will take longer. o Thick, soft material, such as brushed cotton or denim, can be spin-dried at higher speeds. o All fabrics are ironed at the same temperature. There is no risk of overheating. The only factor that varies according to the fabric being ironed is the ironing time. o The ironing time depe...
Otros modelos de este manual:Planchas - THB1500/02 (1.95 mb)