Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
4 EN 5 4 Remove all packaging material from the filters. 4 5 Put the air purifier filter back into the appliance. 5 Note Make sure that the s •• ide with the tag is pointing towards you. 6 Place the pre-filer in the appliance. 6 2 Install filters The appliance comes with all filters fitted inside, but you have to remove the packaging of the filters before you can use the appliance. Remove all filters, unpack them, and place them back into the appliance as described below. Tip ••When you remove or insert filters, place the appliance against a wall for more stability. Note •• Insert the filters in the correct position. 1 Place your fingers in the recesses of the side panels and gently pull the top part of the front panel towards you. 1 2 Lift the hooks at the top of the panel out of the top of the appliance. 3 Remove all the filters from the appliance. 3 EN English Note • Make sure that the side with the two projections is pointing towards you, and that all hooks are properly attached to the appliance. 7 To reattach the front panel, inser t the top hooks into the top of the appliance first (1). Then, push the panel against the body of the appliance (2). 127 6 EN English 3 Switch on Air quality indication Color of the air quality Air quality level 1 Plug the air purifier into the power supply. light ring » All lights go on twice and you hear a Blue good beep.Then, the lights go out again. Deep purple fair Red bad AC4012 Control AC4014 Control Panel Panel To switch off the air quality light ring, press the .............................................................. AIR QUALITY button. Note • The air quality light ring automatically goes on when the appliance is switched on. • The appliance automatically starts operating in the FAN SPEED mode. To switch off the appliance 1 2 Press and hold the .. button until the Press and hold the .. button for 2 seconds to switch on the appliance. power-on light goes out. 2 1 » The power-on light and the AIR 2 Unplug the appliance. QUALITY light on the control panel go on. » The air quality ring shows the quality of the air. 2 EN 7 4 Select mode Night mode In night mode, the air filter operates ver y Manual mode quietly. 1 Press and hold the .. button for 2 Manually select the fan speed. seconds to switch on the appliance. Note • When you manually select a fan speed, you can also use the timer function (see section “Set the timer”). In this case, one of the FAN SPEED lights (AC4012: and ) and the HOUR light ( , , or ) are on. 1 Adjust fan speed 1 Press and hold the .. button for 2 2 Press the button to select night mode. seconds to switch on the appliance. »The light goes on. 1 2 Press the button once or more times to select the desired fan speed. The corresponding fan speed lights show the set fan speed. 2 To change to another FAN SPEED mode, press the button. 2 » For AC4012 - , , or ; and » For AC4014 - , , or . 8 EN English EnglishEnglish Switch on Set the sensitivity of the airquality sensor 1 Plug the air purifier into the power supply. » All lights go on twice and you hear a People with certain health problems (for example: beep.Then, the lights go out again. allergies or asthma) have a greater need for healthy air. For this reason, the purifier allows you AC4012 Control AC4014 Control to adjust the sensitivity of the air quality sensor. Panel Panel If you set it to higher sensitivity level, the purifier starts cleaning the air at lower pollution level. There are 3 sensitivity levels: • standard • sensitive • extra sensitive The pollution sensor is set to standard sensitivity. You can adjust the sensitivity of the air quality sensor in the following way. 2 Press the button to switch on the Note purifier. • When it is set to a higher sensitivity, the » The air quality light shows the current purifier starts cleaning the air at lower air quality. pollution levels to make the air even cleaner. Plug the purifier before adjusting the sensitivity » The fan speed light goes on. of the air quality sensor. 1 Press the .. button and simultaneously put the power plug in the power socket. 3 Press the button to switch off the purifier. » The purifier beeps twice and one of the .. lights ( , , or ) goes on to show the current sensitivity level of the air quality sensor. Timer light Sensitivity level extra sensitive sensitive standard EN 9 Press the button to adjust the 2 Press the button once or more times sensitivity level of the air quality sensor. to select the desired fan speed. » One of the .. lights ( , , or ) goes For AC4012 - , , or ; and » on to show the preferred sensitivity level of the air quality sensor. »For AC4014 - , , or . 3 Press the button to switch off the purifier. Note • When you change the sensitivity, the purifier automatically star ts operating at the set sensitivity level whenever you switch on the purifier. Change the fan speed Manual You can select the desired fan speed. Note • When you select a fan speed, you can also use the timer function (see “Set th...