Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
KICKBACK DANGER Kickback can lead to dangerous loss of control of the Power PrunerTM and result in serious injury to the operator or any one standing close by. Hold the Power PrunerTM firmly with both hands with thumbs and fingers encircling the front and rear handles. Be aware of the down and outward path the pruner will take after the cut is made. Kickback may occur when the moving saw chain at the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. In some cases this may cause a lightning-fast reverse action, kicking the guide bar and saw chain up and back or down and back towards the operator. Either of these reactions may cause the operator to lose control of the Power PrunerTM which could result in serious personal injury. With a basic understanding of kickback, you can reduce or eliminate the element of surprise which contributes to accidents. Avoid contact of the guide bar tip with any object while the saw chain is moving. POWER PRUNERTM ATTACHMENT OPERATOR'S MANUAL 7 Cut only wood. Avoid striking concrete, metal, wire, or other obstructions which could cause kickback or damage to the saw chain. If the saw chain does strike a foreign object, immediately stop the engine, inspect and repair the Power PrunerTM if necessary. EQUIPMENT Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. DESCRIPTION Locate this safety decal on your attachment. Make sure the decal is legible and that you understand and follow the instructions on it. If it cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information. 2. SHAFT DECAL -Contain important safety information that must be followed. 3. LOWER DRIVE SHAFT ASSEMBLY -Contains a specially designed liner and the flexible drive shaft. 4. CUTTING ATTACHMENT -Sealed, gear ratio is 1.5:1 reduction. 5. AUTOMATIC OILER ASSEMBLY -Self oiling. Use high quality, low viscosity, non detergent bar and chain oil. 6. SAW CHAIN -91 VX 9.53mm (3/8 inch) low profile Oregon® saw chain. Runs approximately 609.6 m/min. (2000 ft/min) at full throttle. 7. GUIDE BAR- 254 mm (10 inch) Bar 8. CUTTING SHOE - Used to capture and stabilize branch while cutting. Place cutting shoe against branch, accelerate and lower saw chain into branch. 9. GUIDE BAR COVER -Used to cover guide bar and saw chain during transport and storage. Remove guide bar cover before using unit. P/N 89016022660 1 24 6 7 5 3 8 9 1. GRIP, FRONT -Cushioned grip for left hand. 8 8 CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. 1 Power PrunerTM Attachment -Plastic Bag (co-pack) -Operators Manual -Safety Manual -Warranty Registration Card -Guide Bar Cover -Safety Glasses -Storage Hook Assembly ASSEMBLY POWER HEAD SHAFT/LOWER SHAFT ASSEMBLY Tools Required: None Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling. 1. Set Power Head/Shaft Assembly on a level surface. 2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lockout position. 3. Remove vinyl cap from attachment drive shaft. 4. Carefully fit attachment drive shaft assembly into coupler (B) to decal assembly line (C), making sure that the inner lower drive shaft engages into the square upper drive shaft socket. NOTE Earlier model Power Heads may have shorter couplings. Short couplings fit flush to decal point (E). New couplings are 4-3/4 in. long, and fit flush to line (C). NOTE Lower bearing housing and head assembly must be in line with the engine. A B D C D E POWER PRUNERTM ATTACHMENT OPERATOR'S MANUAL 9 5. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft hole. Insure locator pin is fully engaged by twisting lower drive shaft. Locator pin should snap flush in coupler. Full engagement will prevent further shaft rotation. 6. Secure lower shaft assembly to coupler by tightening clamping knob (D). FRONT LOOP HANDLE REMOVAL Tools Required: Screwdriver. Parts Required: None NOTE Front loop handles/loop handles with barrier bars are not recommended for use with Power Pruner attachment. 1. Remove front handle assembly, barrier bar (if installed), and mounting hardware from PAS or SRM-SB power head. 2. Retain parts for future use. SAW CHAIN TENSION ADJUSTMENT Tools Required: 10 mm (13/32 in.) Wrench, Screwdriver WARNING Always wear gloves when handling saw chain, otherwise serious personal injury may result. To Adjust Saw Chain Tension. 1. Loosen two (2) 6 mm guide bar nuts (A) located on cutting attachment. 2. Turn the adjuster slot (B) clockwise until saw chain touches the bottom of guide bar. Turning adjuster slot (B) counter clockwise will loosen saw chain on guide bar. 3. Tighten guide bar nuts firmly. Move sa...