Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Turn on gas supply to cooker and open gas cock 1. 3. Turn the gas valve control knob 2 anti-clockwise to the position (see Fig. B.). Press down and hold the knob in the position while depressing the piezo ignitor FIG B 3 several times until the pilot has lit. This can be observed through the viewing window 4. 4. When the pilot has lit continue to hold the gas valve control knob for approximately 30 seconds. If it goes out, wait 3 minutes and repeat the procedure holding for a little longer. 5. With the pilot flame established, release the gas valve control knob 2 gradually and rotate anti-clockwise to its low fire position. Where upon the main burner will FIG C automatically light. Leave in the low fire position for at least 30 minutes. NOTE: ANY ATTEMPT TO ROTATE THE CONTROL KNOB BEFORE RELEASE MAY RESULT IN DAMAGE. 6. After 30 minutes rotate the control knob further anti- clockwise to the mid-position of the green band for FIG D normal running (see Fig. D). OFF ON DESN 510252 ‘A’ 5 OFF IGNITION WHITE BLOCK LOW FIRE GREEN BAND NORMAL RUNNING 6 NOTE: AFTER SEVERAL HOURS THE HEAT INDICATOR SHOULD BE ON OR ABOUT THE BLACK LINE IN THE SILVER SECTION. IT MAY BE NECESSARY TO ADJUST THE CONTROL KNOB SLIGHTLY IN THE GREEN BAND TO ACHIEVE THIS. IF THE FLAME HAS EXTINGUISHED FOR WHATEVER REASON, WAIT THREE MINUTES (MINIMUM) BEFORE RE-LIGHTING. 7. On the first lighting or if the cooker has been cold for a long time. moisture from the insulation may run down the enamelled front of the cooker. This should be wiped off to prevent staining. 8. Check the inlet gas pressure is as indicated in the data plate as follows: (i) Turn the gas valve control knob 2 to OFF position (see Fig. A). Remove the inlet pressure test nipple plug 5 and fit pressure gauge. Turn gas valve control knob 2 to the mid position of green band. (ii) Check inlet pressure correctly corresponds to the data plate. (iii)Check that the gas pressure is unaffected when other gas appliances are used. (iv)Turn gas valve control knob 2 to ignition position (see Fig. B). Remove the pressure gauge and replace gas nipple plug. Turn gas valve control knob 2 to the mid-position of the green band for normal running. NOTE FOR L.P. COOKERS ONLY Repeat instruction 8 on completely cold cooker with the pressure gauge fitted to the burner pressure test point 6. Check that the burner pressure correctly corresponds to the table on pages 2 or 3. NOTE: IF FOR ANY REASON A GAS RATE CHECK IS REQUIRED, TURN OFF ALL OTHER APPLIANCES USING GAS AND USING THE GAS METER TEST DIAL AND STOP WATCH, CHECK THAT THE MAXIMUM GAS INPUT IS AS INDICATED ON THE DATA PLATE. Once the correct setting has been confirmed, the heat control will operate automatically to maintain the cooker at full temperature. NOTE: REMEMBER TO NOTE THE SETTING POSITION IF TURNING OFF THE COOKER. INSTRUCTIONS Hand these and the Operating Instructions to the User for retention and instruct in the safe operation of the appliance. Advise the User of the precautions necessary to prevent damage to the Domestic Hot Water System and to be building in the event of the Domestic Hot Water System remaining inoperative during frost conditions. Finally advise the User that, for continued efficient and safe operation of the appliance it is important the adequate servicing is carried out at regular intervals recommended by the Aga Distributor or local Gas Region. 7 With Aga's policy of continuous product improvement, the Company reserves the right to change specifications and make modifications to the appliance described and illustrated at any time. Aga For further advice or information contact your Station Road local distributor/stockist. Ketley Telford Shropshire TF1 5AQ England 8 ...
Otros modelos de este manual:Placas - GCB (139.78 kb)
Placas - GC (139.78 kb)
Placas - GE (139.78 kb)