Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Feed the CONSOLE WIRES through the center hole of the ACCESSORY TRAY MOUNTING BRACKET (Z). Secure the ACCESSORY TRAY to the DISPLAY CONSOLE BRACKET using two 10 mm PHILLIPS SCREWS with WASHERS (13). Tighten the SCREWS securely. Be careful not to pinch the CONSOLE WIRE (X) and HEART RATE WIRE (Y) when securing the ACCESSORY TRAY (V) to the DISPLAY CONSOLE BRACKET (W). Be careful not to let the CONSOLE WIRE (X) and HEART RATE WIRE (Y) fall into the DISPLAY CONSOLE BRACKET (W). Remove the DISPLAY CONSOLE (AA) from its shipping carton. Position the DISPLAY CONSOLE above the ACCESSORY TRAY (V). Connect the CONSOLE WIRE (X), HEART RATE WIRE (Y) (RED), and GROUND WIRE (BB) (GREEN) to the corresponding JACKS located on the back of the DISPLAY CONSOLE. Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE BRACKET (W) using four 12 mm PHILLIPS SCREWS (6) and WASHERS (7). Tighten the SCREWS securely. Do not overtighten the SCREWS. NOTE: NOTE: 5. CAUTION: NOTE: C3-5 Only: Locate the ACCESSORY TRAY (V). Position the ACCESSORY TRAY near the top of the MONOCOLUMN (E) at the DISPLAY CONSOLE BRACKET (W). Item Qty Description C1 5 C3 5 1) 2) 3) 5) 6) 4) 7) 8) 9) 11) 12) C15 & C35 Upright Bikes Hardware List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2 2 2 5 2 10 8 3 3 2 2 1 4 4 2 2 2 5 2 8 8 3 3 2 2 1 2 4 4 50 mm Button Head Screw Button Head Screw Hex Head Bolt Thick Flat Washer - 16 mm O.D. Hex Head Bolt Small Head Phillips Screw Flat Washer - 12 mm O.D. Nylock Nut (on seat) Flat Washer (on seat) Phillips Screw Phillips Screw Phillips Screw w/Locking Compound Phillips Screw w/Washers Button Head Screw Flat Washer - 18 mm O.D. 20 mm 100 mm 60 mm 12 mm 8 mm 6 mm 6 mm 10 mm 15 mm Assembly Guide: Look for the number coded hardware bags that match the assembly sequence. Q 9 8 O P R 11 10 12 T U 1 D 2 B A C AA V CC 14 15 6 W Z 13 DD FF GG EE 6 E HH JJ securing the CONSOLE WIRE to the DISPLAY CONSOLE BRACKET (W). Position the DISPLAY CONSOLE above the DISPLAY CONSOLE BRACKET. Connect the CONSOLE WIRE and HEART RATE WIRE to the corresponding JACKS located on the back of the DISPLAY CONSOLE. Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE BRACKET using four 12 mm PHILLIPS SCREWS (6) and WASHERS (7). Tighten the SCREWS securely. Do not overtighten the SCREWS. Be careful not to let the CONSOLE WIRE (X) and HEART RATE WIRE (Y) fall into the DISPLAY CONSOLE BRACKET (W). Connect the WIRES (DD) leading from the HANDLEBAR ASSEMBLY and the MONOCOLUMN. Slide the HANDLEBAR ASSEMBLY fully into the MONOCOLUMN. Secure the HANDLEBAR ASSEMBLY to the MONOCOLUMN using four 15 mm BUTTON HEAD SCREWS (14) and matching FLAT WASHERS (15). Tighten the SCREWS securely. Be careful not the pinch the WIRES (DD) when sliding the HANDLEBAR ASSEMBLY (CC) into the MONOCOLUMN (E). Locate the RIGHT PEDAL (EE) (marked with an "R") and PEDAL STRAP (FF) (marked with an "R"). With the side of the PEDAL STRAP marked with an “R” facing upward, slide the slotted end of the PEDAL STRAP through the left slot in the PEDAL. Fasten one of the slots onto the tab located under the left slot of the PEDAL. Bend the PEDAL STRAP upward and slide the remaining end of the PEDAL STRAP through the right slot in the PEDAL and into the strap adjustment clip. The PEDAL STRAP should securely engage the strap adjustment clip. Install the RIGHT PEDAL (EE) to the USER RIGHT CRANK ARM (GG). Repeat for the LEFT PEDAL (marked with an "L") and PEDAL STRAP (marked with an "L"). The LEFT PEDAL has reverse threads. Pedals need to be securely tightened or clicking may occur. Locate the WATER BOTTLE BRACKET (HH). Secure the WATER BOTTLE BRACKET to the underside of the MONOCOLUMN (E) using two 12 mm PHILLIPS SCREWS (6). Tighten the screws securely. Insert the WATER BOTTLE (JJ) into the WATER BOTTLE BRACKET. Position the unit in the desired location for use. The unit can be easily moved into place by lifting the rear of the unit and rolling it on the front rollers. Level the unit before use. Refer to the leveling instructions stated in the Operation Manual. C1-5 Only: Remove the DISPLAY CONSOLE (AA) from its shipping carton. While holding the CONSOLE WIRE (X) and HEART RATE WIRE (Y) (RED), cut the wire tie Locate the HANDLEBAR ASSEMBLY (CC). With the handlebars facing forward, position the HANDLEBAR ASSEMBLY near the top of the MONOCOLUMN (E). NOTE: 6. CAUTION: 7. NOTE: NOTE: 8. C1-5 Only: 1. 7. 5. & 6. 8. (C15 Only) Assembly Sequence Monocolumn, Wiring & Cover Rear Stabili...
Otros modelos de este manual:bicicletas - C35 (2.79 mb)