Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions. Specifications Weight Capacity 350 lb. Unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Make sure rubber end caps are se1. cured into feet of Base (2). Steps 2 and 3Steps 6 and 7Steps 4 and 5 U-Shaped BracketPedalLongBolt 2. Insert Long Bolt (6) through: Washer (9);• One hole in U-shaped Bracket un• der Saddle (1); Bushing (10); • Hole in end of Pedal (3); • Bushing (10); • Other hole in U-shaped Bracket; • Washer (9).• Secure Long Bolt 3. with a Lock Nut (8). Insert Short Bolt (7) through:4. Washer (9);• Mounting Bracket (5);• Washer (9);• Remaining hole in Pedal (3);• Washer (9);• Remaining Mounting Bracket (5);• Washer (9).• Secure Short Bolt with a Lock Nut (8).5. Insert remaining Short Bolt (7) 6. through: Washer (9);• Release Bar (4);• Washer (9);• Remaining hole in Mounting Brack• et (5); Washer (9);• Hole in foot on Base (2);• Washer (9);• Remaining hole in second Mounting • Bracket (5); Washer (9).• Secure Short Bolt with Lock Nut (8).7. Before using the Bike Stand with a 8. load, test the operation of the Pedal and Release Bar, without any load, following the operating instructions below. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Locate Stand on hard, flat, and level 1. surface able to withstand load without deforming. Center dirt bike over Saddle and 2. secure to Saddle with tie-down strap (sold separately) before lifting. Using second person to stabilize 3. load, slowly raise Saddle by depressing Pedal with your foot until Saddle is fully raised. Locking Pin (11) R-Pin (12) 4. Insert Locking Pin (11) fully through the hole in the saddle and the base to secure the stand in the up position. Lock it in place with the R-Pin (12) 5. WARNING! Stay clear of Release Bar while Saddle is elevated and in use. Remove tools from under stand be6. fore lowering. To lower Saddle, keep clear and 7. remove the R-Pin and Locking Pin. Place foot on Release Bar and Pedal. Using second person to stabilize load, press on Release bar while guiding Pedal up to smoothly lower Saddle. Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning and Maintenance BEFORE EACH USE,1. inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation. After Use,2. clean external surfaces of the tool with clean cloth. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. Parts List Part Description Qty. 1 Saddle 1 2 Base 1 3 Pedal 1 4 Release Bar 1 5 Mounting Bracket 2 6 M10X70 Bolt (Long Bolt) 1 Parts List Part Description Qty. 7 M10X50 Bolt (Short Bolt 2 8 M10 Lock Nut 3 9 Washer 11 10 Bushing 2 11 Locking Pin 1 12 R-Pin 1 ASSEMBLY DIAGRAM 9 1 8 10 9 8 9 8 9 5 2 9 3 9 6 9 5 9 9 7 9 9 7 4 Note: Locking Pin (11) and R-Pin (12) not shown. Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that...