Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
(These dimensions may vary up to one inch.) An area 4 feet wide x 6.5 feet long is required for safe operation of the Air Fusion 4525 Bike. Make sure that adequate space is available for access to and passage around the Air Fusion 4525 Bike. LEVELING: MOVING: FUNCTION INSPECTION: Visually inspect the Air Fusion 4525 Bike to verify that assembly is as shown in the above illustration. Check the function of the Air Fusion 4525 Bike by turning the crank slowly through one complete revolution to verify that the drive train functions properly. Adjust the TENSION KNOB(29) to verify that the adjustable tension is working properly. Locate and read the WARNING LABEL(78) on the Air Fusion 4525 Bike. Make sure that all users read the WARNING LABEL(78). CAUTION: Adjust the STAND(53) under the FRONT FRAME(1) and the LEVELING CAPS(52) on the REAR STABILIZER(4) so that the Bike sits on the floor without rocking. Remove and reposition the LEVELING CAPS(52) on the REAR STABILIZER(4) to level the Air Fusion 4525 Bike. The Air Fusion 4525 Bike has a pair of WHEELS(51) on the FRONT STABILIZER(2). Lift up from REAR STABILIZER(4) to move the Air Fusion 4525 Bike. To level the Air Fusion 4525 Bike, first screw the STAND(53) located in the middle of the FRONT FRAME(1) all the way up into the FRONT FRAME(1) so that it is not touching the floor. Adjust the two LEVELING CAPS(52) on the REAR STABILIZER(4). When the LEVELING CAPS(52) are adjusted and the Air Fusion 4525 Bike is stable, rotate the STAND(53) to make it contact with the floor. While you are adjusting the LEVELING CAPS(52) the STAND(53) must not be in contact with the floor. Only after the Air Fusion 4525 Bike has been stabilized with the LEVELING CAPS(52) will you position the STAND(53) so it is in contact with the floor to provide extra stability for the frame. EQUIPMENT MAT (not included) OPERATIONAL INSTRUCTIONS SEAT ADJUSTMENT LOAD ADJUSTMENT CAUTION: 1. 2. Rotate the ADJUSTMENT KNOB(49) counterclockwise until the pin releases when the knob is pulled. Pull the ADJUSTMENT KNOB(49) and slide the SEAT FRAME(5) up or down to desired position. Lock the SEAT FRAME(5) in position by inserting the pin of the ADJUSTMENT KNOB(49) into one of the adjustment holes in the REAR FRAME(3), then rotate the ADJUSTMENT KNOB(49) clockwise to lock the SEAT FRAME(5) securely. Sit on the seat and place your feet on the pedals. You should be able to move through a complete pedal stroke without locking your knees or shifting your hips on the seat. The seat is too close to the pedals if you have more than a slight bend in your knees at the bottom of the pedal stroke. The seat is too far from the pedals if you have to completely straighten your knees at the bottom of the pedal stroke. 1. 2. Proper seat adjustment is important. There are twelve adjustment holes in the REAR FRAME(3). These adjustment holes allow users to adjust the position of the seat for efficient exercise. Do not attempt to adjust the seat while you are on the Air Fusion 4525 Bike. Always tighten the ADJUSTMENT KNOB(49) after adjusting the seat to a new position. To increase the load, turn the TENSION KNOB(29) clockwise. To decrease the load, turn the TENSION KNOB(29) counterclockwise. 12 OPERATIONAL INSTRUCTIONS USING THE FITNESS MONITOR OR METER POWER ON: Pedal movement or push the Mode Reset button. POWER OFF: Automatic shut off after four minutes of inactivity. FUNCTION MARKS (On The Display) : M: Speed in Miles Per Hour T : Time : Scan C : Calorie D: Distance : Pulse FUNCTION: SPEED: Displays the current speed on upper display from zero to 999.9 miles per hour. SCAN: Lower display automatically scans each function of DISTANCE, TIME, CALORIE, and PULSE in sequence every four seconds. The function mark "" must appear on display by pressing the button. DISTANCE: Press the button until "D" appears to display the distance you are traveling, from zero to 9999 miles. TIME: Press the button until "T" appears to display the riding time, from one second up to 23 hours 59 minutes. CALORIE: Press the button until "C" appears to display calorie consumption, from one to 9999 Kcal. The Calorie Display estimates the average user's calorie consumption based on the speed and time of the workout. The Calorie Display is not affected by the load adjustment. It should be used only as a comparison between workouts on this unit. PULSE: Displays your heart rate in beats per minute. To display the pulse readout, press the button until only the heart symbol " " is shown on the display. Grasp the Pulse Sensors on both sides of the handrail, one in each hand. The heart symbol " " will begin flashing when the meter senses your heart rate. Your heart rate will be displayed approximately five (5) seconds after the heart icon is displayed. If you do not place your hands correctly and 60 seconds passes without a heart rate reading, the meter will turn off the heart rate circuit. If this occurs, press the button to restart, place your hands back on the Puls...
Otros modelos de este manual:bicicletas - 15-4525 (575.17 kb)