It's a proven fact that a regular exercise program can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise. The Magnetic Fusion 4550 Bike provides a convenient and simple method to begin your assault on getting your body in shape and achieving a happier and healthier lifestyle. Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Read this manual carefully before using the

Connect the PULSE EXTENSION WIRE(40) to the CONTROL WIRE(24). Insert the REAR FRAME(5) onto the FRONT FRAME(1) and secure with BUTTON HEAD BOLTS(M10x1.5x20mm)(66), BUTTON HEAD BOLTS(M10x1.5x53mm) (67), ARC WASHERS(M10)(87), LOCK WASHERS(M10)(89), WASHER(M10)(92), and ACORN NUT (M10x1.5)(85). NOTE: See page 13 for detailed leveling instructions to prevent rocking. ASSEMBLY INSTRUCTIONS 9 B. A. (Assembled at the factory) STEP 5 Refer to illustration A. Attach the HANDRAIL(8) to the SEAT FRAME(7) w

NOTE: Be careful not to damage the wires when attaching the METER(27). 10 11 Locate and read the WARNING LABEL(71) on the Magnetic Recumbent 1350 Bike. Make sure that all users read the WARNING LABEL(71). EQUIPMENT MAT Please note the Rear Frame of the Recumbent Bike is adjustable. Use the longest size to determine the size of the mat. CAUTION: SET UP INSTRUCTIONS Place the Magnetic Recumbent 1350 Bike in the area where it will be used. It is recommended that the Magnetic Recumbent 1350 Bike be

The minimum program time value is 20:00 minutes. Use the UP and DOWN buttons to set the program time from 20 minutes up to 99 minutes in one minute increments. When desired time is displayed press the SET button. The TIME will count down from preset value. 1. 2. STEP 4: Now you are ready to begin exercising. The program will not start until you start pedaling. 15 If two blocks are displayed, your speed is within the acceptable range. If only one block is displayed in the center, your speed match

(These dimensions may vary up to one inch.) An area 4 feet wide x 6.5 feet long is required for safe operation of the Air Fusion 4525 Bike. Make sure that adequate space is available for access to and passage around the Air Fusion 4525 Bike. LEVELING: MOVING: FUNCTION INSPECTION: Visually inspect the Air Fusion 4525 Bike to verify that assembly is as shown in the above illustration. Check the function of the Air Fusion 4525 Bike by turning the crank slowly through one complete revolution to veri

10 SET UP INSTRUCTIONS Place the CPS 9200 Indoor Cycle in the area where it will be used. It is recommended that the CPS 9200 Indoor Cycle be placed on an equipment mat. The CPS 9200 Indoor Cycle is approximately 50 inches long (max.) x 18 3/8 inches wide x 42 5/8 inches tall (max.). An area 4 feet wide x 6 feet long is required for safe operation of the CPS 9200 Indoor Cycle. Make sure that adequate space is available for access to and passage around the CPS 9200 Indoor Cycle. Adjust the STANDS

If just starting an exercise program, work out at the low end of your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your workout by increasing your heart rate. Measure your heart rate periodically during your workout by stopping the exercise but continuing to move your legs or walk around. Place two or three fingers on your wrist and take a six second heartbeat count. Multiply the results by ten to find your heart rate. For example, if your six se

DO NOT BOUNCE! When the pull on the back of the legs lessens, gradually try a lower position. Bent Torso Pulls While sitting on the floor, have legs apart, one leg straight and one knee bent. Pull the chest down to touch the thigh on the leg that is bent, and twist at the waist. Hold this position at least 10 seconds. Repeat 10 times on each side. Floor Stretch While sitting on the floor, open the legs as wide as possible. Stretch the upper body toward the knee on the right leg by using your arm

3 4 DIAGRAM# PART NAME QTY 1 Main Frame 1 2 Stabilizer 2 3 Stand Cap (25.4mm) 4 4 Crank 1 5 Bottom Brake Block 1 6 Top Brake Block 1 7 Press Plate 1 8 Hub Cap 2 9 Nylon Washer (1/2") 2 11 Pedal 2 12 Pedal Strap 2 13 Push Nut (1/2") 2 14 T Knob 1 15 Screw, Round Head (M4 x 12mm) 8 16 Bolt, Button Head (M6 x 1 x 12mm) 6 17 Arc Washer (M6) 6 18 Allen Wrench (4mm) 1 19 Owner's Manual 1 20 Workout Manual 1 21 E Clip (1/2") 2 22 Caution Decal 2 Product Parts Drawing and Parts List FRONT BACK

There are no other warranties other than those expressly set forth herein. Products shipped to the manufacturer must be in the original shipping carton with freight prepaid. All expenses for repairing or replacing the product, including the cost of shipping it back to the original purchaser, will be covered by the manufacturer. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. 3 4 DIAGRAM# PART NAME QTY 1 Main Frame 1 2 Stabilizer 2 3 St