Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
In a ducted application, this rangehood can be vented through the wall or ceiling. To vent through a wall, a 90° elbow is used. When installed ductless, the rangehood vents out of grates on the sides of the chimney. Ductless installations require a Ductless Conversion Kit, available from your dealer. WARNING! BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION, DETERMINE WHICH VENTING METHOD WILLBE USED AND CAREFULLY CALCULATE ALL MEASUREMENTS. FIGURE 1RANGEHOOD ASSEMBLY PLAN THE INSTALLATION The Perla chimneys are adjustable and designed to meet varying ceiling heights as indicated in FIGURE 2. The chimneys can be adjusted for ceilings between 7' 8 1/2" and 9' 9 1/2" depending on the distance between the bottom of the hood and the cooktop (distance x in FIGURE 2). For shorter ceilings, have the chimney cover(s) cut at a sheet metal shop. For higher ceiling installations, the High Ceiling Chimney Kit includes a new 40” upper chimney which would replace the 20” upper chimney that came with the hood. (see OPTIONAL ACCESSORIES page 4) CALCULATE THE DUCTRUN LENGTH 1” min 20” max 22” 9 1/2” 36” x also consult cooktopmanufacturer's recommendation upperchimney lower chimney canopy x = distance from hood to cooktop(varies depending on installation) min -24”, suggested max -30” cabinet base FIGURE 2 19 3/8” min & max ceiling height examples x = 30" min 8' 2 1/2" max 9' 9 1/2" x = 28" min 8' 1/2" max 9' 7 1/2" x = 26" min 7' 10 1/2" max 9' 5 1/2" x = 24" min 7' 8 1/2" max 9' 3 1/2" Theductrunshouldnotexceed35equivalent feet if ducted with the required minimum of 6" round ductwork. Calculate the length of the ductwork by adding the equivalent feet in FIGURE 3for each piece of duct in the system. An example is given in FIGURE 4. For best results, use no more than three 90° elbows. Make sure that there is a minimum of 24" of straight duct between elbows if more than one is used. Do not install two elbows together. If you must elbow right away, do it as far awayfromthe hood's exhaust opening as possible. 3.0 feet 5.0 feet 12.0 feet 0.0 feet 45. Elbow 90. Elbow 90. Flat Elbow Wall CapFIGURE 3 9 Feet Straight Duct 2 - 90. Elbows Wall Cap Total System 9.0 feet 10.0 feet 0.0 feet 19.0 feet FIGURE 4 WARNING Because of the weight and size of the rangehood canopy, two or more people are needed to move and safely install the rangehood canopy. Failure to properly lift rangehood could result in damage to the product or personal injury. PERSONAL INJURY HAZARD Version 07/11 - Page 5 PREPARE THE WALL 1. Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet and rear wall. Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt. 2. Determine and clearly mark with a pencil the center line on the wall where the rangehood will be installed. 3. The canopy attaches to the wall by two mounting brackets (Item 1 in FIGURE 5). The canopy of the rangehood hangs on the two brackets which must be mounted with the flanges on the top of the bracket and pointing away from the wall. Before installing the brackets, the adjustment screws must be installed into the bottom of the bracket. These two screws are provided in the hardware package and have hexagon heads withaslotforaflatbladescrewdriver. Thedimensionsillustrate mounting the canopy 24" above the cooking surface. If a Backsplash is to be used with this rangehood, it must be installed before the rangehood. Installation instructions for the Backsplash are supplied in its box. The height of the Backsplash will determine the bottom edge of the canopy. FIGURE 5 4. The chimney mounts by two brackets (Item 2 in FIGURE 5). Note the position of the brackets. The top bracket should be installed about 1/8" away from the ceiling. The bottom bracket must be installed at the bottom point of the upper chimney sleeve. Determine the proper location for each bracket and install the brackets on the wall. MAKE SURE THAT THE BRACKETS ARE SECURELY FASTENED TO THE WALL. 5. Determine and make all necessary cuts in the wall for the ductwork. Install the ductwork before the rangehood. 6. Determine the proper location for the Power Supply Cable (FIGURE 6). Use a 1 1/4" Drill Bit to make this hole. Run the Power Supply Cable. Use caulking to seal around the hole. DO NOT turn on the power until installation is complete. 30 MODELS 36 MODELS FIGURE 6 INSTALL THE RANGEHOOD 1. Remove the unit from the carton and place on a flat surface for assembly. Cover the surface to prevent accidental damage. Remove all parts including the mounting hardware before discarding the carton. 2. Remove the grease filters from the unit and set aside. The grease filters are removed by pressing the handle in front of the filter (FIGURE 7). When replacing, make sure that the filters are properly positioned with the handles in front and visible. FIGURE 7 3. Remove the cover from the field wiring compartment. Remove the wiring electrical knockout using a flat-b...