Iniciar sesión:
Votos - 1, Puntuación media: 3 ( )

Manual de usuario AEG, modelo DF 6260

Fabricar: AEG
Tamaño del archivo: 285.16 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


• Fully withdraw the vapour catcher of the hood. • Important: Detach and insert the grease filters only when the vapour catcher is fully withdrawn. Remove the grease filters. First remove the rear and then the front grease filter. • For 19 mm side walls, the spacer discs clipped in on the appliance body must be taken out. Mount the hood with 4 or 6 x O 4 mm screws. Fig. 7. Fig. 7 • Insert the hood in the furniture housing and engage both mounting claws (installation aids) on the right and left sides in the side wall of the wall unit and firmly hold the hood for further mounting. Then fix the hood with the 4 or 6 x O 4 mm screws supplied. • Refit the grease filters. Push-in the vapour catcher. • If the cupboard is deeper than 300 mm, cover the gap between the hood and the wall with a finishing strip (special accessory). To install it, proceed as follows: Measure the wall distance and apply the covenng strip over the necessary width (wall distance plus 5 to 8 mm), kinking the covering strip at the appropriate notches and tearing off the surplus material (removing the protective foil). Then fasten the strip to the bottom part of the hood with three clips (special accessories). Apply pressure. Fig. 8. Fig. 8 Fitting the carbon filter for filter version If the fume extractor hood is installed as a return air appliance (Filter version - air outlet above the wall unit), the carbon filter (special accessory) must be fitted before the grease filters are fitted. Installation sequence: 1. Insert the holding frame for the carbon filter in the shaft of the hood with the 2 lugs facing upwards and then clip into the lower holes. 2. Fix the holding frame on the lower part of the housing of the hood with the 2 screws supplied. Fig. 9. 3. Fit the carbon filter (see paragraph “Carbon filter”) 4. Refit the grease filters. Push-in the vapour catcher. Fig. 9 Removing the hood from the wall unit If, for technical reasons (extractor version/filter version conversion) the fume extractor hood has to be removed from the wall unit, proceed as follows: • Fully withdraw the vapour catcher and remove the grease filter. • Loosen the 4 or 6 mounting screws of the hood (wall unit mounting). • To loosen both mounting claws (installation aids), place a max 3 mm dia. Phillips screw-driver in the spring opening and simultaneously press the springs inwards (towards the appliance housing). Fig. 10. Important: Hold the hood firmly! Adjusting the extractor part (E - Fig. 1) - Fig. 11 On wall units with a body depth of 275 mm to 335 mm, the vapour catcher depth can be adjusted as follows: • Remove both grease filters. • Loosen the screws on both end-stop brackets and set the vapour catcher depth (min. 275 mm, max. 335 mm). • Refit the screws. • Refit the grease filters. Fig. 10 Fig. 11 Removing the hood from the wall unit If, for technical reasons (extractor version/filter version conversion) the fume extractor hood has to be removed from the wall unit, proceed as follows: • Fully withdra...

Otros modelos de este manual:
Los aficionados - CHDF 6260 (285.16 kb)
Los aficionados - CHDF 6260 (285.16 kb)
Los aficionados - CHDF 6260 (285.16 kb)
Los aficionados - CHDF 6260 (285.16 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría