Votos - 4, Puntuación media: 3.8 ( )

Fabricar: Miele Tamaño del archivo: 914.86 kb Nombre del archivo: Idioma del manual:

Press the grease filter / active charcoal filter touch control. One or several of the indicator lamps above the – /+ touch controls will flash. The number of flashing lamps shows the percentage of the operating time which has already been used up. 1 lamp = 25 % 2 lamps = 50 % 3 lamps = 75 % 4 lamps = 100 % The operating hours completed remain in memory, even when the machine is switched off or there is a power cut. Operation Altering the filter operating hours counter The operating hours counter for the grease filters is set to 30 hours. This can be lengthened or shortened to suit the type of cooking you do. You can choose from 20, 30, 40 or 50 hours. – Select a short time if you roast or fry a lot. – If you use very little fat for cooking, select a longer time. – If, however, you only cook occasionally we recommend that you select a short time because grease which has built up gradually over a long period of time will harden on the grease filters and make cleaning more difficult. Procedure: Press the On/Off touch control to switch the fan off. Press the run-on option touch control and the grease filter touch control at the same time. The indicator lamp above the grease filter touch control and one of the lamps above the – /+ touch controls will flash. The – /+ touch control lamps show the time which has been set: 1st lamp from the left = 20 hours 2nd lamp from the left = 30 hours 3rd lamp from the left = 40 hours 4th lamp from the left = 50 hours Use the – /+ touch controls to select the desired time. Confirm the selection by pressing the grease filter touch control. If the procedure is not confirmed within 4 minutes of programming the steps, the cooker hood will automatically revert to the "old" data. Operation Setting/altering the active charcoal filter operating hours counter The active charcoal filters are only used for cooker hoods which are set up for recirculation mode. They are not required for vented extraction. On delivery the operating hours counter for the active charcoal filters is set to unlimited. For recirculation mode the operating hours counter needs to be set to the required time: Press the On/Off touch control to switch the fan off. Press the run-on option touch control and the active charcoal filter touch control at the same time. The indicator lamp above the active charcoal filter touch control and one of the lamps above the – /+ touch controls will flash. The – /+ touch control lamps show the time which has been set: 1st lamp from left = 120 hours 2nd lamp from left = 180 hours 3rd lamp from left = 240 hours 4th lamp from left = unlimited Use the – /+ touch controls to select the desired time. Confirm the procedure by pressing the active charcoal filter touch control. If the procedure is not confirmed within 4 minutes of programming the steps, the cooker hood will automatically revert to the "old" data. Cleaning and care Before any cleaning or maintenance work the cooker hood must be disconnected from the mains supply. Ensure that: – it is switched off at the wall socket and the plug has been withdrawn (do not pull on the cable, only on the plug), or – the fuse has been withdrawn from the fused spur connection unit, or – the mains fuse is withdrawn, or – the screw-out fuse is removed (in countries where this is applicable). Housing Warning: The surfaces and controls are susceptible to scratches and abrasion. Please observe the following cleaning instructions: All external surfaces and controls can be cleaned using warm water with a little washing up liquid applied with a soft sponge. Wipe dry using a soft cloth. Do not use too much water when cleaning the controls. Water could penetrate into the electronics and cause damage. Avoid: – cleaning agents containing soda, acids or chlorides, – abrasive cleaning agents, e.g. powder cleaners or cream cleaners, – abrasive sponges, e.g. pot scourers or sponges which have been previously used with abrasive cleaning agents. These will damage the surface material. Stainless steel Stainless steel surfaces can be cleaned using a proprietary non-abrasive cleaning agent designed specifically for use on stainless steel. To help prevent re-soiling, proprietary conditioning agents for stainless steel can also be used. Apply sparingly with an even pressure. E-Cloth A microfibre "E-Cloth" is available from the Miele UK Spare Parts Department, Part Number 98013530, which is suitable for cleaning surfaces such as stainless steel, glass, plastic and chrome. Stainless steel coloured controls These controls may suffer discolouration or damage if soiling is left on them for too long. Remove any soiling straight away. Do not use stainless steel cleaning agents on these types of controls. Cleaning and care Grease filters Re-usable metal filters are fitted which remove solid particles (oil, dust, etc.) from the kitchen vapours, preventing soiling of the cooker hood. The filters should be cleaned regularly (at least every 3-4 weeks) to avoid a build-up of fat, but ...

Descargar ahora

Introduzca dos números de la imagen: