Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
• Connect the air outlet connection 15 to the hood body outlet using either a flexible or rigid pipe o 150 mm, the choice of which is left to the installer. • Ensure that the activated charcoal filters have been inserted. EN 7 ELECTRICAL CONNECTION • Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. • Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. 7.2.1 Flue assembly Upper exhaust flue • Slightly widen the two sides of the upper flue and hook them behind the brackets 7.2.1, making sure that they are well seated. • Secure the sides to the brackets using the 4 screws 12c (2,9 x 9,5) supplied. • Make sure that the outlet of the extensions pieces is aligned with the chimney outlets. Lower exhaust flue • Slightly widen the two sides of the flue and hook them between the upper flue and the wall, making sure that they are well seated. • Fix the lower part laterally to the hood body using the 2 screws 12c (2,9 x 9,5) supplied. 12c22.12.212c12c EN 8 USE Control board Key Function Display A Switches the extractor motor on and off at the latest selected speed Indicates the selected speed. B Decreases the suction speed. The number of lit LEDS decreases. C Increases the suction speed. The number of lit LEDS increases. D By pressing this key it is possible to start the intensive speed from any previously selected speed except the Delay-function and 24H-function. This speed has been timed at 10 minutes. After that time the system activates automatically the latest selected speed. This function is suitable for cooking conditions when vapours and smells are at the utmost emission. I flashes and the LEDS are all lit. By pressing the key the function is stopped. E By pressing this key it is possible to set up the motor to a suction speed at 100 m3/h . 24 appears and the LEDS extinguish one by one. By pressing the key the function is stopped F By pressing this key it is possible to set the delayed shutdown of the motor and the lighting to 30 minutes. This function is suitable for a complete elimination of residual cooking odours. Functioning only when the motor is on(not during the 24H-function or intensive function). By pressing the key the function is stopped A flashing clock-symbol appears. By pressing the key the function is stopped G By pressing this key for about 2 seconds it is possible to reset the filter saturation alarm After 100 working hours a drop-symbol appears. Metal grease filters have to be washed. After 200 working hours C appears. Charcoal filters have to replaced. H By pressing this key the intensity of the lighting system can be decreased. I Switches on/off the lighting system at the maximum intensity. L By pressing this key the intensity of the lighting system can be increased. Keyboard lock: it is possible to jam the keyboard when, for example, cleaning the glass. The motor and lights are switched off. By pressing the F-key (Delay) for about 5 seconds the keyboard block can be activated or deactivated. This function is confirmed by a Beep and by moving motor LEDS on display. EN 9 MAINTENANCE REMOTE CONTROL (OPTIONAL) The appliance can be controlled using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03AAA type. • Do not place the remote control near to heat sources. • Used batteries must be disposed of in the proper manner. Cleaning the Comfort Panels • Pull the Comfort Panel to open it. • Disconnect the panel from the hood canopy by sliding the fixing pin lever. • The comfort panel must never be washed in a dishwasher. • Clean the outside using a damp cloth and neutral liquid detergent. • Clean the inside as well using a damp cloth and neutral detergent; do not use wet cloths or sponges, or jets of water; do not use abrasive substances. • When the above operation has been completed, hook the panel back to the hood canopy and close it by turning the knob in the opposite direction. EN 10 Metal grease filters Metal filters can be washed also in a dish machine. They need to be washed every time a drop-symbol appears in the display or at least every two months. In case of very frequent use these have to be washed even more often. Alarm reset • Press the G-key for at least 2 seconds. Cleaning • Open the comfort panel. • Remove the filters one by one by pushing them backwards and pulling them down contemporaneously. • Wash the filters. Pay attention not to bend them. Make sure that filters are completely dry before putting them into their seat. (a possible modification of the filter surface doesn’t influence its efficiency). • Place the filters again into their seats and make sure that the handle of the filter remains outside. • Close the comfort panel. ATTENTION: Remove the filters one by one pushing them towards the back side of the hood and simultaneously pulling downwards and towards the centre...
Otros modelos de este manual:Los aficionados - RMG1H60SG (512.79 kb)