Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 3   Tamaño del archivo: 871 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

The side panels have keyhole-shaped cutouts. Push the side bungs which blank off the charge control knob aperture, panels over the screws and push downwards. 20. Screw the side panels tightly (screw A). DO NOT OVERT1GH- 21. Fit the charge control knob and room thermostat control knob TEN THE SCREWS. Assembly is now finished. over their spindles in the right-hand side panel. 5 23. Finally, disconnect the electricity supply and connect each supply cable to a suitable double pole switch adjace

Descargado: 1   Tamaño del archivo: 871 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

No loops of cable should be left behind or underneath the unit. Core space cover 5. Stability The heater must be fixed securely to a solid wall to prevent movement. A screw with wall plug is provided in the accessory pack to secure the heater. The assembled heater must be able to resist a horizontal pull of at least 200N on its upper edge without toppling or shifting. If the required stability cannot be achieved with the supplied accessories, e.g. in the case of light-construction walls, th

Descargado: 6   Tamaño del archivo: 871 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

Note also the information given on the appliance. 1. THIS HEATER IS VERY HEAVY, BEFORE INSTALLING ENSURE THAT THE SUPPORTING SURFACE IS STRONG ENOUGH TO SUPPORT THE WEIGHT OF THE HEATER (SEE BELOW “INSTALLED WEIGHTS“). IN ORDER TO MAINTAIN STABILITY AND TO ENSURE ITS FUTURE SAFETY IN USE, IT IS ESSENTIAL THAT IT IS SECURED TO A SOUND WALL BY MEANS OF THE FIXING SUPPLIED. IRREGULAR SURFACES SUCH AS MAY RESULT FROM CARPETS OR TILED SURROUNDS PARTIALLY PROTRUDING UNDER THE HEATER SHOULD BE AVOIDED

Descargado: 1   Tamaño del archivo: 636 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

In order to maintain stability, it is essential that the heater be placed on a level surface and care should be taken to avoid irregular surfaces, such as may result from carpets or tiled surrounds partially protruding under the heater. The heater feet are designed to go underneath a carpet rather than standing on it; this permits the weight to be taken on a firm base. Carpet gripper should be removed from behind the heater feet. BRICKS: The heater casing and the heater storage bricks with whic

Descargado: 2   Tamaño del archivo: 636 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

If ° load rating only is required the installer should move the black wire as indicated in the circuit diagram. ELEMENT ASSEMBLY (WITH SAFETY CUT OUT) WARNING Remove the inner front panel; this carries on it's inner face the front insulation slab. Handle this with care, the insulation must not be damaged. REMOVE ALL THE PACKING CARDBOARD FROM INSIDE THE STORAGE BRICK COMPARTMENT, IF LEFT INSIDE IT WILL BE SET ON FIRE WHEN THE HEATER IS SWITCHED ON. ENSURE THAT ALL PACKAGING MATERIAL IS REMOV

Descargado: 7   Tamaño del archivo: 636 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

When a new heater is run up to temperature/ the materials will produce a slight smell for the first few days/ these are normally harmless in a well ventilated room. It is best to make these first overnight charges with the 'Input' control knob at 'Maximum'. Caged birds, young children and people with chest ailments are best kept out of the room for this first period. output Supaslim Combi * 6 n\j 1 mm m SETTING THE CONTROLS The controls are located under the lockable flap at the right hand

Descargado: 1   Tamaño del archivo: 636 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

skirting size is 1 5 x 120mm. Note that the smallest wall spacing should be used only when the skirting board is of the modern slim type, or there is no skirting board at all. MUST STAND VERTICAL You must fit a retaining screw at each end of the heater. 100mm {4") Skirling Goarrf —Lf'"' Outer Siol 1 SOmm i6“> Skirting Beard It THE HEATER A clear space of at least 3" (75mm) must be left at either side of the heater, and any projections or shelves must be at least 10" (250mm) above the h

Descargado: 1   Tamaño del archivo: 636 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

Two supplies are taken into this heater, both fan heater and storage heater circuits must be connected to the same phase of the electricity supply. IF, DURING ANY REASSEMBLY OF THE HEATER, A PART OF THE THERMAL INSULATION SHOWS DAMAGE OR DETERIORATION WHICH MAY IMPAIR SAFETY, IT SHOULD BE REPLACED BY AN IDENTICAL PART WALL FIXING: The heater must ALWAYS be mounted against, and fixed to a wall as it will not stand up by itself. A detachable bracket is provided for screwing to the wall, the heate

Descargado: 1   Tamaño del archivo: 636 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

Nos: TSR12CW TSR18CW TSR24CW TSR12ACW TSR18ACW TSR24ACW C( This appliance conforms to îhe following EEC Directives: low Voltage Equipmenl Electromagnetic Compatibility 73/23/EEC 89/336/EEC 93/68/EEC 92/31 /EEC 93/68/EEC IMPORTANT NOTES: It is important to read these instructions carefully and also note the information given on the heater itself. As these particular instructions refer to the assembly and installation of a new heater, they should be retained by the installer; not left behind

Descargado: 1   Tamaño del archivo: 366 kb   Fabricar: Creda  
Categoría: Los aficionados
@name

* TSR6AW/MW have no user controls and are IPX2 rated (drip-proof) ChargeCharge Acceptance (7 hrs)Acceptance (8 hrs) • Elements (storage) - mineral insulated stainless steel sheathed • Insulation - opacified silicaceous aerogel and mineral fibre mat • Storage Core - high density iron oxide compound • Controls* (Output) - manually adjustable thermostat controlling output damper. • Controls (Input) - hydraulic charge control thermostat, manually adjustable • Protection - two level thermal safety ov





Categoría