Votos - 3, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
• Make sure the tape is not at its end. • Make sure a programme has been set for timer recording. • Make sure your timer settings are past the current time. • Check that the decoder is turned on. • Check that the satellite tuner is turned on. • The clock stops if the VCR is disconnected from the mains. Reset the clock and timer. • Turn the power off and unplug the mains lead. Additional Information continued Troubleshooting Symptom Remedy Timer recording The SHOWVIEW menu or the TIMER PROGRAMMING menu does not appear. • Check that TIMER METHOD in the EASY OPERATION menu is set correctly (see page 73). The VPS/PDC function does not operate properly. • Check that the clock and the date are set correctly. • Check that the VPS/PDC time you set is the correct one (there might be a mistake in the TV programme guide). If the broadcast you wanted to record did not send the good VPS/PDC information, the VCR will not start recording. • If the reception is poor, the VPS/PDC signal might be altered and the VCR might not start recording. Synchronized Recording The SYNCHRO REC button turns off while recording or does not go back to recording standby mode. • The tape has reached its end. Insert a new tape and press SYNCHRO REC again. The Synchronized Recording function does not work. • The connected equipment was not turned off. Turn off the connected equipment and press SYNCHRO REC again. • There was a power failure. Press SYNCHRO REC again. The programme recorded with the Synchronized Recording function is incomplete. • If the settings for timer recordings and Synchronized Recording overlap, the programme that starts first has priority and the second programme starts recording only after the first programme has finished. • There was a power failure. Press SYNCHRO REC again. Canal Plus You cannot watch Canal Plus programmes when the VCR is in standby mode. • Check that DEC is set to ON for this channel in the TV STATION TABLE menu. • Make sure the Canal Plus Scart cable is plugged securely. A Canal Plus programme is always recorded scrambled. • Make sure the Canal Plus Scart cable is plugged securely. • Check that DEC is set to ON for this channel in the TV STATION TABLE menu. Troubleshooting Symptom Remedy Others A tape cannot be inserted. • Check that a tape is not already in the tape compartment. The remote commander does not function. • Make sure you are pointing the remote commander at the remote sensor on the VCR. • Replace all the batteries in the remote commander with new ones if they are weak. • Make sure the [TV] / [VIDEO] remote control switch is set correctly. The selected input line connector number does not appear in the display window. • Press INPUT SELECT to display the connected line. The tracking meter does not appear on the TV screen. • The recording condition of the tape is very poor and tracking cannot be adjusted. You cannot control other TVs. • Set your TV’s code number. The code number may change when you replace the batteries of the remote commander. The display window becomes dim. • The display window automatically becomes dim when the VCR is in standby or timer recording mode. The VCR needs to be cleaned. • Clean the cabinet, panel and controls with a dry, soft cloth, or a soft cloth slightly moistened with a mild detergent solution. Do not use any type of solvent, such as alcohol or benzine. The Line Through function does not operate. • Set POWER SAVE in the USER SET menu to OFF (see page 71). Additional Information Symptoms caused by contaminated video heads • Normal picture • Rough picture • Unclear picture • No picture (or black & white screen appears) initial terminal contamination Troubleshooting Specifications System Channel coverage PAL (B/G, D/K) VHF E2–E12, R1–R12 UHF E21–E69, R21–R69 CATV S1–S41, S01–S05 RF output signal UHF channels 21–69 Aerial out 75-ohm asymmetrical aerial socket Tape speed SP: PAL/MESECAM 23.39 mm/s (recording/playback) NTSC 33.35 mm/s (playback only) LP: PAL/MESECAM 11.70 mm/s (recording/playback) NTSC 16.67 mm/s (playback only) EP: NTSC 11.12 mm/s (playback only) Maximum recording/playback time 10 hrs. in LP mode (with E300 tape) Rewind time Approx. 1 min. (with E180 tape) Inputs and outputs LINE-1 (EURO AV) 21-pin Video input: pin 20 Audio input: pins 2 and 6 Video output: pin 19 Audio output: pins 1 and 3 LINE-2 (DEC/EXT)/LINE-3 (DEC/EXT) 21-pin Video input: pin 20 Audio input: pins 2 and 6 t LINE-2 L o R*1 VIDEO IN, phono jack (1) Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO IN, phono jack (2) Input level: 327 mVrms Input impedance: more than 47 kilohms AUDIO (OUT/SORTIE) R/D L/G*2 Phono jack (2) Rated output level: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms *1 SLV-SE840N only *2 not available on SLV-SE640N and SE440K General Power requirements 220 – 240 VAC, 50Hz Power consumption • SLV-SE440K 15 W 1.2 W (POWER SAVE is set to ECO2, minimum) • SLV-SE640N 17 W 1.2 W (POWER SAVE is set to ECO2, minimum) • SLV...
Otros modelos de este manual:VCR / vídeo - SLV-SE640N (818.51 kb)
VCR / vídeo - SLV-SE740N (818.51 kb)
VCR / vídeo - SLV-SE840N (818.51 kb)
VCR / vídeo - SLV-SX740N (818.51 kb)