Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Enter Camera IP address Enter Home Camera Page Enter Login Window23You Will Enter Home Page After Login 3. 1Install ActiveX When the username and password are confirmed, a control setup screen pops up under the IE address bar. Click “Install ActiveX Control” to install the controls. 2The security warning screen aps. Click Install. Network Camera Live & Control Page3StepThe ActiveX is powered by Uniform Technologies and You need to press Install to enable media viewer on your IE browser ActiveX plug-in. When ActiveX Plug-In is installed then you can view video image. If you can not see, please select streaming mode to HTTP. Please refer to User Manual for detail operation. Install Internet Explorer Plug-In Components If No Video Image You may need to check your PC environment including (1) Window Firewall setting (2) IE version should be 6.0 or above. You may need to check router/firewall setting if you view the video from the other side of router/firewall. You may refer to user manual to learn this in depth. NetServer 6001/P/W Video Server Quick Guide ©2007 Asante Networks Inc., All rights reserved. NetCam is a registered trademark of Asante Network, Inc. Wireless networking POWER Alarm Infrared inductor Alarm HUB Video in DVR Digital Video Recorder AMP MIC AMP WAN Internet PTZ Surveillance RS485 Alarm input Alarm output 2. 1. Connect your analog camera using Connect Video cable. RS-485 to this product. 6. Connect the switch hub to your PC (as shown in the figure). 5. Connect the product to the switch hub(as shown in the figure.) 4. Connect the product to the power source. Link Connect RS-485 Cable 5. 4. 6. Step Connect the product to the switch/hub and analog camera Connect the video server using LAN. 3. Connect your camera to the power source (as shown in the figure) Connection diagram If No Switch/Hub You may connect Ethernet direct from PC to product. However, you will need to confirm your IP address to the existing network. You may also need a crossover cable. It is highly recommended that you have an IT professional assist you. Search for the product from your LAN. The factory IP setting 192.168.0.20 appears on the screen. Run the IP Finder.exe file from the CD. 1 4 Submit the change Open the IE browser Tools Internet Options Security Custom Level Note: This product supports IE 6.0 or above. Step Step IP Address settings Start When you find the camera, click it and the settings appear on the right side. Change the settings for the new network environment you need. Change the Internet Explorer settings 2 Search the product on the network . 3 Changing the IP address, Netmask, Default Gateway 4 Click Submit to validate new settings. 4 5 Confirmation You may “search” again to confirm the change is correct. After that, you can “exit”. Bring Up Your IE browser Start Make sure that Level II, the commonly used default security level, is set for the security. 2Check Steps 4 OK Click OK to quit. 1 3 Select “medium” for security Step Wireless Setting After setting of Ethernet IP address, enter the Wireless Setting page. 1Start Wireless Setting Wireless Bandwidth Primary time of WLAN or 802.11 b/g offers 11Mbps or 54mbps share bandwidth. The WLAN bandiwdth is much less than that offered by Ethernet switch which can sustain multiple channels of milti-mega bits of realtime stream data like video. Due to the bandwidth limitation of WLAN, It is HIGHLY recommended to set video Quality below 1.5Mbps and below. If your signal strength from wireless router/AP is below 50%, either you need to adjuest AP or camera position or boost antenna power. Please consult your network manager. Camera will automatically scanned Wireless APs when you enter the page, or you may press “scan” again. Importantly, you need to ensure your WLAN AP is shown and with encyption enable. 2Search/Select Wireless AP . Select Infrastructure mode, auto and enter SSID, Select WEP Encryption to be 64 bits or 128bits depending on your wireless router/AP setting. Enter the exact same KEY that your used for the wireless router/AP. Select DHCP or enter static IP address based on your network plan. Press “Save”. 3Setting the Network Paramaters 4Refresh/reload page. After few seconds, you should see the new wireless IP address. Wireless Setting Confirm Relocate Camera and Final Test StepUnplug the RJ45 on both router and the network camera so that you can start to use wireless independently. Unplugged Ethernet 1Relocate & Mount Device. Please mount the device to the preferred location and power on the device. 2You may “Test” if it has been connected and operated smoothly. 1) Set Up your PC on the same WLAN subnet. 2) Use IP Finder to identify the Network Camera. 3) Use IE brower to view the video 4) Check to make sure that wireless signal strength is at least 50%. 5) Check to make sure that the Video Quality is set lower than 1.5Mbps 6) View the video. Test & RUN 3StepWireless Setting After setting of Ethernet IP address, enter the Wireless Set...