Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
B B Return to the normal screen. Press SET UP. NOTES: . If you have a satellite receiver or a decoder connected to the L-2 IN/DECODER connector, be sure to set “L-2 SELECT” back to appropriate mode after editing. . If you are not connecting a satellite receiver or a decoder to the L-2 IN/DECODER connector, leave “L-2 SELECT” set to “VIDEO”. . When “L-2 SELECT” is set to “SAT VIDEO” and “SAT S-VIDEO”, “SAT” appears on the TV screen or front display panel instead of “L-2”. . If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set “L-2 SELECT” to “DECODER” or “SAT VIDEO”. . If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2 SELECT” to “DECODER” or “SAT S-VIDEO”. . If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT VIDEO”, “SAT S-VIDEO” or “DECODER”, be sure to connect the L-1 IN/OUT connector with a TV. F-1 Input Setting (F-1 INPUT) Set “F-1 INPUT” to the appropriate mode depending on the connector (VIDEO or S-VIDEO) being used on the front panel. Perform steps A and B of “L-1 Output and L-1 Input Setting (L-1 OUTPUT and L-1 INPUT)” on page 84. A A Select the input mode for the VIDEO/ S-VIDEO connector. A Press rt to move the arrow to “F-1 INPUT”, then press ENTER. B Press rt to select the appropriate setting, then press ENTER. (The boldface settings in the table below indicate the settings at your purchase.) 8 F-1 INPUT VIDEO: When connecting an appliance to the VIDEO input connector, set to “VIDEO”. S-VIDEO: When connecting an appliance to the S-VIDEO input connector, set to “S-VIDEO”. B B Return to the normal screen. Press SET UP. 86 EDITING (cont.) Digital Audio Dubbing . Turn on the TV and select the AV mode. . Slide the TV/CABLE/SAT/DVD switch to DVD. Recorder Rear of unit Note for connection: Remove the protection cap from the cable. Digital audio device (MD deck, etc.) Optical cable (not provided) DIGITAL AUDIO OUT (OPTICAL) Player Coaxial cable (not provided) DIGITAL AUDIO OUT (COAXIAL) You can dub selected audio from a DVD or Audio CD disc to a digital audio device. However, it is not possible to dub copy-protected discs. Example: Dubbing to an MD A A Make connections. Connect the unit and a digital audio device using either an optional optical cable or an optional coaxial cable. B B Place a disc and load an MD. For the unit A Press x to open the disc tray. B Place a disc on the disc tray. C Press x to close the disc tray. For the digital audio device Load an MD. C C Prepare the unit for dubbing. A Select the audio to be dubbed. B Start playback slightly before the actual point from where you wish to start dubbing. C Press 9 to pause playback. D D Prepare the digital audio device for dubbing. Select the input mode. E E Start dubbing. A Press 4 to start playback on the unit. B Start recording on the digital audio device. F F Stop dubbing. Stop recording on the digital audio device. Then press 8 to stop playback on the unit. NOTE: There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts. REMOTE CONTROL Remote Control Functions Remote 1/2/3/4 Code Switching The remote control is capable of controlling four JVC video units independently. Each of the units can respond to one of four codes (1, 2, 3 or 4). The remote control is preset to send 1 code signals because your unit is initially set to respond to 1 code signals. You can easily modify your unit to respond to 2, 3 or 4 code signals. Slide the TV/CABLE/SAT/DVD switch to DVD. On the remote control Keep pressing SET UP down during steps A – B. A A Change the remote control code. Press the number key “1” for 1, “2” for 2, “3” for 3 or “4” for 4. B B Set the remote control code. Press ENTER to set the code. On the unit C C Turn off the unit. Press 1 on the unit. D D Display the code. Press 4 on the unit for over 5 seconds while the unit is turned off. . The code currently set appears on the front display panel. E E Change the unit’s code. Press 8 on the remote control. . The code currently set on the remote control blinks on the front display panel for approximately 5 seconds, and is applied to the unit. NOTE: When “POWER SAVE” is set to “ON” (. pg. 95), it is not possible to change the remote code. REMOTE CONTROL (cont.) TV Multi-Brand Remote Control Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer’s TVs can also be controlled. Before performing the following steps: . Turn off the TV using its remote control. . Slide the TV/CABLE/SAT/DVD switch to TV. IMPORTANT: Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability. A A Set the TV brand code. Keep pressing SET UP down during step A. Enter your TV’s brand code using the number keys, then press ENTER. Press TV/CBL/SAT 1 on the unit’s remote control to turn on the TV and try operations ( step B). . Once...
Otros modelos de este manual:Vídeo - LPT0827-001B (8.47 mb)