The other push buttons can be used to operate another opener and/or light control product. The 33LM 3-Button Remote Control Remote control can also be used with a 423LM 3-channel receiver and a 3-button door control to operate a commercial door opener in open, close, and stop mode (as explained on side 2). To match or change the code in the remote control Locate the code switches in both the new and the original remote controls. The new remote control’s code switches can be found by sliding the

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. TO CHANGE AN EXISTING, KNOWN PIN If the existing PIN is known, it may be changed by one person without using a ladder. 1. Press the four buttons for the present PIN, then press and hold the # button. The opener light will blink twice. Release the # button. 2. Press the new 4-

This door control contains a motion detector that will automatically turn on the light when it detects a person entering the garage. This feature can be easily turned off for extended work light use. Locate the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. NOTE: After installation, an indicator light behind the cover will indicate proper connection. If not lit, the Lock and

The unit’s memory can store up to four fingerprints. • The term “enroll” refers to scanning the fingerprint so the device will recognize the user. • The term “swipe” refers to the movement of the finger across the sensor strip. • The term “LED” stands for Light Emitting Diode. There are 6 LEDs located on the Fingerprint Keyless Entry. When unit is on, it is programmed to shut off after a short period of time. The unit’s sensor strip is sensitive so it is important to read the Tips for Success be

NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. INSTALLATION • Unplug the opener before proceeding. • OPEN RECEIVER: Insert a small screwdriver in slot on receiver front panel as shown. Twist up actuator cover. • C

See Figure 14. 2 Retighten the cam. Doc 01-G0674 Rev E Optional Accessories 19 Optional Accessories CAUTION Turn off power before working inside gate enclosure. Vehicle Detectors Almost all types of vehicle detectors may be used in conjunction with both model BG770 and BG790. More than one detector may be connected to the gate, and may be mounted inside of the cabinet. Connect the detector(s) according to the instructions on the wiring diagrams supplied with the gate and with the detector itself

Accessories ______________________________________________________________________ 23 3. Primary Voltage Circuit ____________________________________________________________ 23 4. Low Voltage Circuit _______________________________________________________________ 24 General Reference Information_________________________________________________________ 25 Doc 01-G0674 Rev E Contents Required Maintenance-Normal Usage_____________________________26_Toc509797299 BG770 Drawing and Parts List_________

OPTIONAL AC Adapter Input A Ensure Base Station and PIR Motion Sensor are in close proximity to each other. Press and release Learn Button on Base Station. Buzzer will sound. B Within 60 seconds, press the Learn Button on the inside of the PIR Motion Sensor. LED light will illuminate and Base Station will buzz. Learn Button 1 2 PIR Motion Sensor SWITCH #1: SWITCH #2: 3 4 Learn Button Insert battery pack facing away from circuit board and fasten cover with the smallest screws (provided). NOTE: En

NOTE: The Base Station is intended for indoor use only. Carton Inventory Swivel Bushing Sun/Rain Shield Mounting Plate AC Adapter Base Station Passive Infra-Red (PIR) Motion Sensor Rubber Pads Operation & Features Volume Antenna On/Off Button BASE STATION On/Off: To turn the Base Station on and off, hold down the power button until you hear the on/off tone. Volume: The Base Station is equipped with adjustable volume controls. The lowest volume setting is the mute feature. Batteries: If the AC ad

Para PRUEBA: Ponga el interruptor de tiempo (ON-TIME), al fondo del detector, en la posicion de prueba (TEST) y DUALBRITE®a apagado (OFF). TEST 1 5 20ON-TIMEOff 3 6 Dusk to DawnDUALBRITE® Para AUTOMATICO: • Tecnologia DUALZONE™. • Prende la luz cuando detecta movimiento. • Apaga la luz automaticamente. • Temporizador crepuscular. • Lafotocelulamantienelaluzapagadaduranteeldia. • LED indica que se ha detectado movimiento (durante el dia o la noche). Para MODO MANUAL: ...prendalo. 1 segundo APAGA