Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Crown Tamaño del archivo: 6.19 mb Nombre del archivo: Idioma del manual:

The three (3) digit panel identification numbers shown in the charts are also stamped along the bottom edge of each panel. Refer to Figures 20 and 21. c. Rearward and Intermediate panels have reverse bend flanges on one side of panel. These panels must be installed prior to forward panels. NOTICE To install multiple side panels, start at the rear of boiler and work forward. To remove panels, reverse order of assembly. d. If boiler is equipped with tankless heaters they should be installed at this time if they were not installed for hydrostatic test outlined on Page 18. e. Install right side panels into position by inserting top of panel into ‘U’ shaped channel, pushing bottom of panel in toward boiler, and sliding panel down into ‘J’ shaped channel. Repeat procedure until all right side panels are in place. f. Remove the knockouts necessary for tankless heater operation on left side panels. g. Install left side panels, using the same procedure used to install the right side panels. JACKET LEFT SIDE PANEL USAGE CHART BOILER MULTIPLE LEFT SIDE PANELS* MODEL PANEL 1 PANEL 2 PANEL 3 PANEL 4 PANEL 5 24-03 L10 L5 24-04 L10 L11 24-05 REAR OF BOILER L10 L17 FRONT OF BOILER 24-06 L10 L18 L5 24-07 L10 L18 L11 24-08 L10 L18 L17 24-09 L10 L18 L18 L5 24-10 L10 L18 L18 L11 24-11 L10 L18 L18 L17 24-12 L10 L18 L18 L18 L5 RIGHT SIDE PANEL USAGE CHART BOILER SINGLE / MULTIPLE RIGHT SIDE PANELS* MODEL PANEL 3 PANEL 2 PANEL 1 24-03 R15 (SINGLE) 24-04 R21 (SINGLE) 24-05 R E IO B F O T N O R F R27 (SINGLE) R E O B LL O R A E R 24-06 R33 (SINGLE) 24-07 R15 R24 24-08 R21 R24 24-09 R27 R24 24-10 R27 R30 24-11 R33 R30 24-12 R21 R24 R24 *NOTE: TO INSTALL MULTIPLE SIDE PANELS, START AT THE REAR AND WORK FORWARD. TO REMOVE PANELS, REVERSE ORDER OF ASSEMBLY. Figure 20: Left Side Panel Usage Chart Figure 21: Right Side Panel Usage Chart 23 Figure 22: Series 24 Jacket Assembly (Boiler Models 24-03 thru 24-12) 8. Combination Label and Crown Logo Plate were attached to jacket front panel at time of manufacture. If loose or peeling, apply pressure to reset adhesive. 9. On steam boilers, attach lowest permissible water level plate (from steam trim carton) to the front panel using sheet metal screws. 10. Tighten all sheet metal screws to complete jacket assembly. 11. RTC Bracket (if used)- install bracket in top right corner of front panel with four (4) #8 x 3/4” self tapping screws. F. BURNER MOUNTING PLATE - Refer to Figures 16 and 23. 1. Using silastic sealant, secure the 3/16” diameter rope gasket to the groove along the mounting plate opening in the front section. 2. Install 5/16” x 1” lg. cap screw in lower tapping on front section to carry weight of burner mounting plate. 3. Engage bottom slot on burner mounting plate with matching bolt in bottom tapping of front section. Align mounting holes and fasten the mounting plate to the boiler sections with seven (7) remaining 5/16” cap screws and washers. Fully tighten all bolts. G. MOUNT BURNER ADAPTER PLATE TO BURNER MOUNTING PLATE. Refer to Figures 16 and 23. 1. 2. In all cases the burner adapter plate carton for the specified burner will be provided by Crown. Open Adaptor Plate carton and remove contents. Apply four (4) small dabs of silastic on rear surface of adapter plate to temporarily hold gasket in place. Hold adapter plate in position against burner mounting plate, align holes and secure with five (5) 3/8” lock washers and 3/8” x 7/8” lg. cap screws. 3. Follow burner manufacturer’s instructions using gasket material and hardware provided with burner. 4. USE A HOLE SAW OR KNIFE TO CUT BURNER MOUNTING PLATE INSULATION TO MATCH HOLE SIZE ON BURNER ADAPTER PLATE. After cutting, remove any and all loose pieces of insulation which may become lodged or interfere with the head of a burner air tube after insertion. Confirm that hole in insulation fits snugly around burner blast tube. If hole is oversized, use fiberglass rope gasket provided with burner to fill in any space between insulation and blast tube. If rope gasket is not provided with the burner, use 3/8” fiberglass rope (provided by others). 5. For boilers without tankless heaters, proceed to Step H (Install Steam Trim) or I (Install Water Trim). 6. For boilers with tankless heaters, install the tankless heater manifolds according to Figure 37. CAUTION Failure to properly fill all gaps between the insulation and burner blast tube may result in damage to the burner STANDARD BURNER ADAPTER PLATE BECKETT C"CF" SERIES] BURNER ADAPTER PLATE ' B'DIA BOLT CIRCl BOILER MODEL PART NO. I .D NO. DIA. 'B' DIA. REF. 24-03 THRU 24-05 330400 920 4? 10 24-06 THRU 24-08 330401 921 6g 10 7ffe 24-09 THRU 24-12 330402 922 6| 10 7fk BECKETT C *CG" SERIES) BURNER ADAPTER PLATE BOILER MODEL PART N0. I .□ ND. ' DIA. □ IA. REF. 24-03 THRU 24-06 330400 920 4-3/4 10 24-07 THRU 24-08 330401 921 6-1/8 10 24...

Descargar ahora

Introduzca dos números de la imagen: