Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
(Removal of the kick panel is necessary to access plate.) HCB1/2(B) Riveted to front right-hand corner of the lower shelf. GHIR44 Riveted to the door liner behind the left hand door panel. IR1/2(B) Riveted to lower cabinet bottom shelf. Gas Data Model Dimensions No. of Burners per Section Total BTU /hrWidth Depth Height GHCB40 34” 391/8” 79” 4 100,000 GHCB44 34” 391/8” 79” 4 100,000 GHMCB44 34” 391/8” 57” 4 100,000 HCB1 36” 383/8” 68” 4 50,000 HCB2(B) 36” 383/8” 801/2” 4 100,000 IR1 36” 383/8” 69” 4 80,000 IR2(B) 36” 383/8” 801/2” 4 160,000 GHIR44 34” 381/4” 82” 4 80,000 TOOLS Standard • Hand tools (standard set) • Volt-Ohmmeter (VOM) with AC current tester (any quality VOM with a sensitivity of at least 20,000 ohms per volt can be used). • Gas test kit • Temperature tester (thermocouple or digital pyrometer) • Temperature tester (thermocouple type). • Manometer – 4 – IMPORTANT STOP BOLTS MUST BE IN POSITION FOR SAFE OPERATION OF GRID. IF DAMAGED OR MISSING, REPLACE AT ONCE. DO NOT OPERATE GRID WITHOUT BOLTS. Two (2) broiler grid 1/4-20 stop bolts and nuts are supplied with each broiler grid to ensure that the grid is not accidentally pulled completely from the broil section while hot. One (1) stop bolt and nut are mounted to the grid carriage RT. and LT. HD. side member through a 0.281 diameter hole directly in front of the grid stop tab. The stop nuts and bolts are screwed tightly against the side members and are properly adjusted extending approximately 1/2” below the stop tab as shown in the above photo. – 5 – REMOVAL AND REPLACEMENT OF PARTS COVERS, PANELS AND HANDLES Burner Box Cover (GHCB40, GHCB44, GHIR44) WARNING: SHUT OFF THE GAS BEFORE SERVICING. 1.Open the augratin oven door. 2.Remove the oven rack. 3.Remove the four screws and bushings from the oven. 4.Remove the augratin oven bottom assembly as outlined in Augratin Oven Bottom Assembly. 5. Lift and remove the burner box cover from the broiler. 6. Reverse the procedure to install. Burner Shield Cover [HCB2(B), IR1, IR2(B)] WARNING: SHUT OFF THE GAS BEFORE SERVICING. NOTE: The models HCB2(B) and IR2(B) have two burner shield covers. 1.Remove the two screws from the burner shield cover and the broiler. 2.Lift and remove the burner shield cover from the broiler. 3.Reverse the procedure to install. – 6 – Manifold Cover Assembly (GHCB40 & GHIR44) WARNING: SHUT OFF THE GAS BEFORE SERVICING. 1. Remove the grease tray from the broiler 1. Loosen the mounting screw in each burner(GHCB40 only). knob. NOTE: The GHIR44 manifold cover assembly has 2. Remove the burner knob. a chain to protect switch wiring. 2. Loosen the mounting screw in each burner knob. 3. Remove the two burner knobs from the broiler. 4. Remove the two screws from the manifold cover assembly. 5. Remove the manifold cover assembly from the broiler. 6. Reverse the procedure to install. Burner Knob Cover Plate [ HCB2(B), IR1 and IR2(B)] WARNING: SHUT OFF THE GAS BEFORE SERVICING. 3.Remove two screws from the burner knob cover plat...
Otros modelos de este manual:Calentadores de Agua - GHCB40 (10.64 mb)
Calentadores de Agua - GHCB44 (10.64 mb)
Calentadores de Agua - GHIR44 (10.64 mb)
Calentadores de Agua - GHMCB44 (10.64 mb)