Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Make sure that there is cold air circulation in the appliance. The temperature in the Products are too near to each Store products so that there is freezer is too high. other. cold air circulation. Replacing the lamp The appliance is equipped with a longlife LED interior light. Only service is allowed to replace the lighting device. Contact your Service Center Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Service Center. TECHNICAL DATA Dimension of the recess Height 1850 mm Width 560 mm Depth 560 mm Rising Time 21 h Voltage 230-240 V Frequency 50 Hz The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. 18 18 Installation INSTALLATION WARNING! Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance. Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: Climate class Ambient temperature SN +10°C to + 32°C N +16°C to + 32°C ST +16°C to + 38°C T +16°C to + 43°C Electrical Connection CAUTION! Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING! This appliance must be earthed. The manufacturer declines any liability should these safety measures not be observed. 12345 The wires in the mains lead are coloured in accordance with the following code: Installation 19 135 Green and Yellow: Earth Brown: Live Blue: Neutral As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: 1. Connect the wire coloured green and yellow to the terminal marked either with the letter “E“ or by the earth symbol or coloured green and yellow. 2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or coloured black. 3. Connect the wire coloured brown to the terminal either marked with the “L“ or coloured red. 4. Check that no cut, or stray strands of wire is present and the cord clamp 4 is secure over the outer sheath. 5. Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. 6. Switch on the appliance. The appliance is supplied with a 13 amp plug fitted 2 . In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that it is disposed of safely. Door reversibility The door of the appliance opens to the right. If you want to open the door to the left, do these steps before you install the appliance: 1. Loosen the upper pin and remove the spacer. 2. Remove the upper pin and the upper door. 20 20 Installation 3. Unscrew the pins (B) and spacers (C). 4. Remove the lower door. 5. Loosen the lower pin. On the opposite side: 1. Install the lower pin. 2. Install the lower door. 3. Refit the pins (B) and the spacers (C) on the middle hinge on the opposite side. 4. Install the upper door. 5. Tighten the spacer and tighten the upper pin. Ventilation requirements The airflow behind the appliance must be sufficient. B C C 50 mm min. 200 cm2 min. 200 cm2 Installing the appliance CAUTION! Make sure that the mains cable can move freely. Do these steps. Installation 21 1. If necessary cut the adhesive sealing strip and then apply it to the appliance as shown in figure. 2. Drill the hinge cover A, as shown in figure. Apply the covers A and A1 (in the accessories bag) in to the middle hinge. 3. Install the appliance in the niche. Push the appliance in the direction of the arrow (1) until the upper gap cover stops against the kitchen furniture. Push the appliance in the direction of the arrow (2) against the cupboard on the opposite side of the hinge. x x A A1 2 1 22 22 Installation 4. Adjust the appliance in the niche. Make sure that the distance between the appliance and the cupboard front- edge is 44 mm. The lower hinge cover (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is correct. Make sure that the clearance between the appliance and the cupboard is 4 mm. Open the door. Put the lower hinge cover in position. 5. Attach the appliance to the niche with 4 screws. 6. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case. 44mm4mmII Installation 23 7. Attach the covers (C, D) to the lugs and the hinge holes. Install the vent grille (B). Attach the hinge covers (E) to the hinge. 8. If the appliance must connect laterally to the kitchen furniture door: a) Slacken the screws in fixing brackets (H). b) Move the brackets (H). c) Retighten the screws. 9. ...
Otros modelos de este manual:Refrigeradores - SCT71900S0 (820.13 kb)
Refrigeradores - SCT71900S0 (820.13 kb)
Refrigeradores - SCT71900S0 (820.13 kb)
Refrigeradores - SCT71900S0 (820.13 kb)