Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
other. cold air circulation. There is too much frost. Food is not wrapped correctly. Wrap the food correctly. The door is not closed correctly. Refer to "Closing the door". The temperature regulator is Set a higher temperature. not set correctly. Replacing the lamp 1. Disconnect the mains plug from the mains socket. 2. Remove the screw from the lamp cover. Technical data 15 3. Remove the lamp cover (refer to the illustration). 4. Replace the used lamp with a new lamp of the same power and specifically designed for household appliances. (the maximum power is shown on the lamp cover). 5. Install the lamp cover. 6. Tighten the screw to the lamp cover. 7. Connect the mains plug to the mains socket. 8. Open the door. Make sure that the lamp comes on. Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Service Center. TECHNICAL DATA Dimension of the recess Height 1446 mm Width 560 mm Depth 550 mm Rising Time 20 h The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. INSTALLATION WARNING! Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance. Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: 16 16 Installation Climate class Ambient temperature SN N ST T Electrical connection +10°C to + 32°C +16°C to + 32°C +16°C to + 38°C +16°C to + 43°C Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply. The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician. The manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with the E.E.C. Directives. Door reversibility The door of the appliance opens to the right. If you want to open the door to the left, do these steps before you install the appliance: 1. Loosen and remove the upper pin. 2. Remove the upper door. 3. Remove the spacer. Installation 17 4. Loosen the middle hinge. 5. Remove the lower door. 6. Loosen and remove the lower pin. On the opposite side: 1. Tighten the lower pin. 2. Install the lower door. 3. Tighten the middle hinge. 4. Install the spacer. 5. Install the upper door. 6. Tighten the upper pin. Ventilation requirements The airflow behind the appliance must be sufficient. 50 mm min. 200 cm2 min. 200 cm2 Installing the appliance CAUTION! Make sure that the mains cable can move freely. Do these steps. 18 18 Installation 1. Install the appliance in the niche. Push the appliance in the direction of the arrow (1) until the upper gap cover stops against the kitchen furniture. Make sure that the distance between the appliance and the cupboard front- edge is 44 mm. Push the appliance in the direction of the arrow (2) against the cupboard on the opposite side of the hinge. Make sure that the clearance between the appliance and the cupboard is 4 mm. 2. Adjust the appliance in the niche. The plastic spacer (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is correct. Open the door. Put the plastic spacer in position. 3. Attach the appliance to the niche with 4 screws. 1244mm4mmII Installation 19 4. Apply the adhesive sealing strip to the appliance as shown in figure. 5. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case. 6. Attach the covers (C, D) to the lugs and the hinge holes. Install the vent grille (B). Attach the hinge covers (E) to the hinge. BEDC 20 20 Installation 7. Disconnect the parts Ha, Hb, Hc and Hd 8. Install the part Ha on the inner side of the kitchen furniture. 9. Push the part Hc on the part Ha. ca. 50 mm ca. 50 mm 21 mm 90° 90° 21 mm Ha Hc Installation 21 10. Open the appliance door and the kitchen furniture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes. 11. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). 12. Place the small square on the guide again and fix it with the screws supplied. Align the kitchen furniture door and the appliance door by adjusting the part Hb. Ha Hb 8 mm Ha K 8 mm Hb 22 22 Environmental concerns 13. Press the part Hd on the part Hb. Do a final check to make sure that: • All screws are tightened. • The sealing strip is attached tightly to the cabinet. • The door opens and closes correctly. Hb Hd ENVIRONMENTAL CONCERNS The symbol ...
Otros modelos de este manual:Refrigeradores - SCS51400S0 (605.53 kb)
Refrigeradores - SCS51400S0 (605.53 kb)
Refrigeradores - SCS51400S0 (605.53 kb)
Refrigeradores - SCS51400S0 (605.53 kb)