Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
DANGER. Before using adapter as illustrated, be certain that center screw of outlet plate is grounded. The green-colored rigid ear of lug extending from adapter must be connected to a properly grounded outlet, make certain it is grounded. If necessary, replace original outlet cover plate screw with a longer screw that will secure adapter ear lug to outlet cover plate and make ground connection to grounded outlet. MOUNTING: The Battery Charger may be set on a table or a shelf. Do not set charger on floor. It should be mounted such that the air intake louvers are at least 18 inches from the floor. Regardless of how it is placed, the top and side louvers of the unit must not be blocked. This is a convection cooled charger and blocking the louvers will damage the unit. When locating the unit, take into account the number of batteries to be recharged and location of the recharging racks. Never place the charger such that battery acid or water may be spilled in the top of the unit. Never place the unit directly over the batteries to be charged. Fumes caused by gassing batteries will be drawn through the charger by convection and cause damage to the unit. CONTROLS: AMMETER: Indicates the amount of current that the batteries are receiving. The larger the amount of current, the faster the batteries will charge. All batteries in a series group will receive the same amount of current. Do not exceed 6 amps charge rate. MAIN POWER SWITCH: This switch turns the power off to the entire charging unit. Any time the charger is not being used, this switch should be turned off to conserve energy. CHARGE RATE SWITCH: These switches may be used to adjust the charging current the batteries will receive. An off position on these switches will disconnect power from the clamps. One of these switches or the main power switch should be off whenever handling the output clamps. If the charger is not going to be used for a period of time, turn the main power switch off to conserve energy. Turning off only a charge rate switch will not have the same effect. CAUTION ! ! ! When a number of batteries are connected in series, a high DC voltage exists at the terminals of the end batteries. When not connected, the charger DC leads will have no output voltage but the battery terminal may still present a shock hazard. SERIES CHARGING: Connecting batteries in series (see illustration) allows a person to charge a number of batteries at one time using only one low current, high voltage charger. The amount of charge that each battery receives is indicated by the ammeter. Thus, each battery will arrive in a fully charged condition at a different time. Conditions that affect charging time are battery temperature, size, state of charge, type of battery, and other factors. Six and twelve volt batteries may be intermixed when series charging. The total voltage of the batteries should not exceed the rated voltage of the charger. Example: A Charger is rated a nominal 36 cells. Six 12 volt batteries in series or twelve 6 volt batteries in series can be charged or any combination of six and twelve volt batteries that total 36 cells. To charge batteries in series, connect the charger's positive lead to the positive post of the first battery. Connect a jumper from the negative post of the first battery to the positive post of the next battery. Continue until all batteries are connected. Attach negative lead of charger to remaining battery post. Dark area represents state of charge of battery. At start of charge 3 Remove battery when it becomes fully charged Charger output voltage must be turned down after battery is removed At finish of charge, turn main power switch "Off" to conserve energy When a battery is fully charged, it must be removed from the charging circuit. If it is not, it may be damaged by over charging. END OF CHARGE: Discontinue charge when three successive hydrometer readings taken at half hour intervals fail to show an increase in specific gravity, or when battery begins to gas excessively or when temperature of electrolyte reaches approximately 120EF. If a battery is sealed and these determinations cannot be made, see manufacturer's instructions for charging. WIRING DIAGRAM MODEL 6080A PARTS LIST 605675 - Switch w/knob (1) 610057 - Handle (optional accessory) 610172 - Switch - Rocker 610072 - Side panels (1 pair) 605616 - Ammeter 610075 - Top panel 605206 - AC Cord 610076 - Base 610098 - DC Cable set 610082 - Back panel 610117 - Circuit Breaker 610083 - Front panel 610090 - Rectifier 6074 - Jumper leads (set of 5) 610088 - Transformer 4 Parts may be purchased from your local authorized service depot listed in the Service Procedure Manual supplied with your product. If you elect to order parts from the factory you may do so by mail or phone. Minimum order from the factory is $25.00. Orders received that are under the minimum will not be processed. Taxes and freight are extra and are not considered to be part of the dollar value of the order. W...