Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
2. Connect the battery clamps correctly by matching the red clamp, which is Positive (+), to the Positive (+) terminal on your battery. 3. Connect the black clamp, which is Negative (-), to the Negative (-) terminal on your battery. *Follow this carefully to not cause any bodily harm. Connecting Using Bare Wire Adaptor 1. Connect the Bare Wire connector to the SolarFlat extension chord. 2. Securely connect bare wire cables to adjoining positive and negative cables. *Note that negative bare wire cable is the cable without writing on black sheath of wire. Mounting: For optimal performance, choose a high sunlight area and place securely with solar panel side facing directly towards the sun. *Note: Do not screw holes directly through front of frame. This will cause damage to solar product. Installation: Connecting Using Battery Clamps: 1. Connect the Battery Clamp connector to the SolarFlat extension cord. 2. Connect the battery clamps correctly by matching the red clamp, which is Positive (+), to the Positive (+) terminal on your battery. 3. Connect the black clamp, which is Negative (-), to the Negative (-) terminal on your battery. *Follow this carefully to not cause any bodily harm. Connecting Using Bare Wire Adaptor 1. Connect the Bare Wire connector to the SolarFlat extension chord. 2. Securely connect bare wire cables to adjoining positive and negative cables. *Note that negative bare wire cable is the cable without writing on black sheath of wire. Mounting: For optimal performance, choose a high sunlight area and place securely with solar panel side facing directly towards the sun. *Note: Do not screw holes directly through front of frame. This will cause damage to solar product. Always test outdoors under optimal sunlight conditions. A. Testing SolarFlats for Voltage General Testing Protocol (For Solar Charge Controller) THESE PRODUCTS ARE WARRANTED FROM DEFECTS IN WORKMANSHIP AND Limited Warranty Notes: Notes: • SolarFlat LED Test Light can be connected to extension cord to indicate that solar panel is functioning properly. • SolarFlat LED Test Light can be connected to extension cord to indicate that solar panel is functioning properly. Connect Voltmeter to each individual panel separately and observe open voltage. Open FUNCTIONALLITY FOR A PERIOD INDICATED ON THE • SolarFlat includes blocking diode to prevent • SolarFlat includes blocking diode to prevent Voltage can range from 16 Volts to 24 Volts. PACKAGING. THIS reverse current. reverse current. Once all panels are tested for voltage, proceed to step B. B. Test Connection to Charge Controller for Voltage. Reconnect SolarFlats, can connect to Charge Controller as per Charge Controller instructions. Measure open circuit voltage at the battery side of the Charge Controller. Open circuit should read 5-10% lower than without Charge Controller, resulting in measurement between 15V and 23.5V. C. Connect Charge Controller to Battery. First, disconnect solar panels and connect Charge Controller to battery. Always connect Charge Controller to battery first and remove last. Observe polarity – positive to positive and negative to negative. D. Reconnect Solar Panels to Charge Controller. If battery voltage is 14.2 or higher, the GREEN light should be on. If battery voltage is between 13 and 14.2, the YELLOW light should be on. If battery voltage is 13 or lower, the Yellow light should be on. If all testing results with voltages within the above indicated ranges, solar system is in acceptable range. If voltage reading indicates lower ranges, repeat above connections and retest. WARRANTY DOE NOT APPLIY IN THE EVENT OF MISUSE OR ABUSE OF THE PRODUCT, OR AS A RESULT OF UNAUTHOURIZED REPAIRS OR ALTERATIONS. POWER OUTPUT IS WARRANTED UP TO 80% OF STATED OUTPUT AND MUST BE TESTED UNDER FULL SUNLIGHT CONDITIONS. TO ADDRESS WARRANTY ISSUES, PLEASE CONTACT BRUNTON, INC. CUSTOMER SERVICE: 2255 BRUNTON COURT RIVERTON, WY, USA, 82501 PHONE: 307.857.4700 WWW.BRUNTON.COM FAQs: 1. Can I use the panel outdoors? A. Yes, this panel has been weatherproofed. 2. What type of batteries can my SolarFlat 2 charge? A. All 6V batteries like ones used in deer feeders and cameras. 3. Can I overcharge my battery? A. The SolarFlat 2 has a built in blocking diode that prevents battery discharge and overcharging. 4. Will the SolarFlat 2 keep my battery fully charged? A. The Maintainer charges your battery with the power of the sun. It compensates for key offdrain and long periods of non-use and on board electronics. It is designed to maintain batteries. 5. How long does it take to charge a dead battery? A. The unit is designed to maintain batteries only. If the battery is dead, we recommend a larger output solar charger such as the 5W or 15W Brunton SolarFlats. 6. Can I extend the wire? A. The 12’ wire can be extended up to 24’ without loss of power of voltage damage. FAQs: 1. Can I use the panel outdoors? A. Yes, this panel has been weatherproofed, including UV protection and for weather ef...
Otros modelos de este manual:cargadores - SolarFlat 15W/12V (724.62 kb)
cargadores - SolarFlat 2W/12V (724.62 kb)