(IT) Selezionare "FLAT" per una completa risposta in frequenza. (D) Wählen Sie "FLAT" für einen compleate Frequenzbereich vor. (SP) Seleccione "FLAT" para una gama de frecuencia del compleate. (Eng) Select "HIGH" for a high frequency range. (FR) Choisissez la "HIGH" pour une gamme a haute fréquence. (IT) Selezionare "HIGH" per la risposta delle frequenze alte. (D) Wählen Sie "HIGH" für eine Hochfrequenzstrecke vor. (SP) Seleccione el "HIGH" para una gama de alta frecuencia (Eng) The cut fre

Luxembourg, Mendriso Branch 3 Moree St., CH 6850 Mendrisio Switzerland р г Front/Rear view 1 i H J M 71 ij 0j J 2 <> DO^DP HJFT ""\ *** N s* REN m — . t % c Q=D(Mll @01= ■CH (u! (u) »™ Ml IE 1 32 u O -± oN) +12V GND REM E Low Level Input Fuse K Gain Controll E 12V (DC) power terminal E Low pass switch ¿6 Remote terminal Low pass cutting adjustment GND terminal S Multiplayer x1/x10 switch for Low section + Left channel terminal (+ MONO) S'

Harman Consumer Part No. GTOAMPOM12/04 Group International Specifications and appearance are Chateau-du-Loir, France 12/04 subject to change without notice.

Part No. GTOAMPOM1/04 JBL Consumer Products

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 425W RMS x 1 channel @ 4 ohms and .1% THD + N* • 700W RMS x 1 channe

SubwooferRightLeft– + + – + – GTO755.6 II (partial end panel) 5 APPLICATIONS – GTO755.6 II The GTO755.6 II can be configured for 6-channel, 5-channel or 3-channel operation, as shown in Figures 9 through 11. Input Mode Switch: • Use INT (internal mode) to send a signal from the front and rear inputs to the subwoofer. • Use EXT (external mode) when sending a dedicated signal to the subwoofer inputs; e.g., if your source unit has a subwoofer output. NOTE: For simplicity, Figures 9 through 11 do no

Set both parts aside. 4. Locate the enclosed hardware bag and remove the four clips. Each clip has a square end and a larger round end. Using a round end, press two clips onto each neon tube (e.g., Street Glow AN9 or equivalent), as shown in Figure 13. 5. For each tube, align both clips so the square ends slide onto an exposed extrusion edge, as shown in Figure 9. Do not cover any screw holes. When installed correctly, each neon tube will sit under an extrusion and not be visible when viewed fro

EXT/INT Switch • If the source unit has a subwoofer output and you have connected it to the SUB input, set this switch to the EXT position. Otherwise, set it in the INT position. Subwoofer Remote Level Control Connector • Connect the Remote Level Control (RLC) here, using the supplied RJ-11 cable. Subwoofer Level Control • Used to match the SUB input of the amplifier to the output of the source unit. • See for adjustment procedures. Protect LED • Illuminated under any of the following fault cond

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 55W RMS x 4 channels, plus 225W RMS x 1 channel, @ 4 ohms and .1% TH

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 225W RMS x 1 channel @ 4 ohms and <1% THD + N* • 360W RMS x 1 channe