The 12 o'clock position is a great starting point. EXAMPLE: Ifyou adjust the High Pass to 100Hz. the amplifier will not play trequencies below 100Hz but will play trequencies trom 100Hz to the chosen Low Pass trequency. -When in Low Pass/Bandpass operation, this setting acts as a low frequency cut off for your system reproduction aka Subsonic Filter. The point that you set it at cuts off any trequencies trom reproduction beyond this point. The 12 o'clock position is a great starting point. EXAMP

To the desired frequency or position. 13. Once the system is powered up, set the volume control on the head unit to about the 2 O’clock position, and then set all the amplifiers’ level controls for maximum output level. 14. Further fine tuning of the various controls may be m\necessary to obtain the desired results. Installation & Precautions Precautions 1. Before you drill or cut any holes, investigate your car's layout very carefully. Take care when you work near the gas tank, fuel line

sub sonic filter switch This selector switch permits the bass level an increase of 18dB. bass boost level control This control permits adjustment of the bass level up to an increase of approximately up to 18dB. sub sonic control When the sub sonic selector switch is in "ON" mode, this filter control permits continuously variable adjustment from 10 to 100Hz. low level Input This amp features RCA type jacks for high impedance input. Use these with car stereo output which uses RCA type connector c

3. Input Level Controls -Enables the matching of input levels to the output levels from the head unit( or other signal source). 4. Variable Subsonic Filter - 15Hz~40Hz (VIBE1801D), 10Hz - 40Hz (VIBE3200D) 5. Low Pass Filter -When Crossover Mode Selector is in Low Pass Mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 50Hz~150Hz. 6. Variable Bass Boost Control -0 ~ +18dB 7. Phase Shift -Allows you to

Always test the speakers and their wires first. Amplifier will not power up. Check for good ground connection. Check that remote DC terminal has at least 13.8v DC. Check that there is battery power on the + terminal. Check all fuses. Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. High hiss or engine noise (alternator whine) in speakers. Disconnect all RCA inputs to the amplifier(s)-if hiss / noise disappears, then plug in the component

Speaker Impedance 2 (Sim 2 Ohm 2 Ohm 2 Ohm T.H.D 0.04% 0.04% 0.04% 0.04% Frequency Response i5Hz~35kHz, - ldB 15HZ-35ICHZ, - ldB !5Hz-35kHz, - ldB i5Hz-35kHz, - ldB Input Sensitivity ioomV-4c>oomV i00mV-4000mV ioomV-400omV i00mV-4000mV Input Impedance 22 kOhm 22 kOhm 22 kOhm 22 kOhm S/N Ratio >90dB >9odB >9odB >9odB Channel Separation >65dB >65dB >65dB >65dB Crossover Filters Low Pass High Pass Bandpass 40Hz-350kHz 4oHz-3kHz n/a 40Hz-350kHz 40HZ-3 kHz n/a 40Hz-350kHz 4oHz-3kHz n/a 40Hz-35

You have purchased a quality product designed and engineered to give uau many gears of uncompromlsed musical service. VECTOR series amplifiers are designed with Hie latest technologg available, which provides headroom for even the most demanding peaks and dgnamlc ranges found on modem CD's and recordings. VECTOR Owner's Manual table of contenis features and specifications VCT-2DIO features and specifications VCT-26IO features and specifications VCT-4IIO features and specifications VCT-I5Ü

Ground (10.5-16V) 270x452x558 10,63 x 1.78x21.97 rjhwznr VECTOR Owner's Manual - 4 features and controls 2 ch amp VCT-25IO bass boost level control power terminals © OOOOOOOO — "I" <12 e • ooOOOOOO JEL @ speaker connections power fuse jCatuar V ECTOR Owner's Manual features and specifications 4 ch amp VCT-4IIO fiMlumcf ciftnl When used with normal, full range system, set this switch to "FULL ‘ If you wish to use the inlerml crossover hi power a driver or specific frequen

Tighten the screws securely. When making electrical connections to your amplifier, please observe the following: Use at least 8 gauge wire for power and ground connections. Wire ttie amplifier directly to the car battery. For the ground connection, use the shortest possible wire to a good chassis ground point. Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna. About power fuses: Lanzar Vector Series amplifiers feature built-in fuse systems. The

You have purchased a quality product designed and engineered to give you many years of uncompromised musical service. Vibe amplifiers are designed with the latest technology available, incorporating a DC to DC Switching Power Supply, which provides headroom for even the most demanding peaks and dynamic ranges found on modem CD’s and recordings. TABLE OF CONTENTS i Table of Contents Features and Controls 1 vibe 211/221/231/241/251/261 2 vibe 411/421/431 3 vibe 531 4 Specifications 6 Installati