Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Make sure pool water is midway of skimmer opening. NOT PRIME: 2. Make sure strainer basket is not clogged. 3. Make sure strainer basket is positioned properly! 4. Tighten lid down snugly. 5. Make sure strainer pot is full of water. 6. TIghten all fittings and seal all joints on suction side. 7. Clean skimmer and pump strainer baskets. 8. Remove pump lid and check for clogging. 9. Open all valves in return and suction lines. 10. Remove and replace pump seal if needed. 11. Check voltage at pump to be sure it is same as motor specs. B. LOW FLOW 1. If filter gauge reads high. a. Filter is dirty. b. Clogged return lines. 2. If filter pressure gauge reads low. a. Pump or skimmer strainer basket is clogged. b. Skimmer or main drain valve is closed. c. Air leak in suction line. d. Impeller setting is incorrect. e. Debris on impeller vanes. C. MOTOR 1. Motors will run hot to the touch, however, they are designed this way. Thermal RUNS HOT overload protector will function to turn the motor off if there is an overload problem. 2. Factors which will increase operating temperature: a. Installed in direct sun. b. Poor ventilation. c. Low voltage. d. Wiring is incorrect size for load. D. MOTOR WILL 1. Check that all power switches are on, fuse not blown, and circuit breaker NOT TURN is not tripped. 2. Timer improperly set. 3. Impeller is against volute face. SAVE THESE INSTRUCTIONS. LIMITED PWARRANTY PUMPS PENTAIR POOL PRODUCTS, INC. pumps are warranted to be free from defects in material and workmanship. Should any of the operating parts become defective within one year from date of purchase, they will be replaced or repaired if defect is proved to be the responsibility of PENTAIR POOL PRODUCTS, INC. All adjustments are to be based on list prices in effect at the time of adjustment. PENTAIR POOL PRODUCTS, INC. will not be liable for the cost of labor or removing or replacing parts. Purchase agrees to prepay all shipping charges to and from PENTAIR POOL PRODUCTS, INC. 1620 Hawkins Ave., Sanford, NC 27330 or 10951 West Los Angeles Ave., Moorpark, CA 93021, whichever is closer or more convenient. This warranty does not cover failure in service due to fire, wreckage, freezing, willful abuse, improper repackaging or damage incurred in shipping nor does it extend to consequential damages. 35-7000 Printed in the U.S.A. Rev. B 5/2005 HYDROPUMP® AND ENERGY MASTER™ HYDROPUMP® TWO SPEED POOL AND SPA PUMP INSTALLATION, OPERATION & SERVICE MANUAL INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS GENERAL: Our shipping container has been specifically designed to prevent transit damage. However, any indications of damage should be carefully noted on the delivery ticket and a claim filed promptly with the carrier. LOCATION: Locate the pump as close as possible to the pool. Provide the necessary space around the pump for future inspection and servicing of the unit. If possible, allow several inches of clearance below the motor to floor to allow easy access to mounting screw. Locate away from pool chemicals to prevent spilling on or near motor. INSTALLATION: The pump suction line should not be smaller than the pipe size on the inlet of the pump. Your pump is made of the finest engineering materials available today. A few simple precautions taken during the initial installation, will insure many long years of trouble-free operation. The threads of pipe fittings screwed into pump must be sealed with: pipe sealant, Teflon® Tape, R.T.V. or other sealing materials approved for pipe threads. Tighten the pump fitting only as much as is required to insure a tight connection. DO NOT OVER TIGHTEN. The piping should be supported independently and not supported by the pump. The pump motor must be wired for the proper voltage, and rotation, in accordance with the wiring diagram supplied with the motor. All wiring should be done by a licensed electrician in accordance with local codes, be certain that the motor frame is grounded. Use lug on top of motor frame to bond together motor and all metallic parts of pool, spa or hot tub structure and to all electrical equipment, metal conduit, and metal piping within 5 feet of the inside walls of a swimming pool, spa or hot tub, when the motor is installed within 5 feet of the inside walls of the swimming pool, spa or hot tub structure with a solid copper conductor not less than No. 8 A.W.G. Motor name plate has voltage, phase, ampere draw and other motor information. Terminal cover plate or name plate has wiring connection information. The wiring to motor should be kept as short as possible and large enough to carry the necessary current for required length without excessive voltage drop. The following table should be followed to be sure that the proper wire size is selected. Use as a guide only. TABLE OF A.W.G. WIRE SIZE FOR SINGLE-PHASE POOL PUMP MOTORS H.P. WIRE LENGTH 50 FEET 100 FEET VOLTS 115 230 VOLTS 115 230 1/3 14 14 14 14 1/2 14 14 12 14 3/4 12 14 12 14 1 12 14 10 14 1 1/2 10 14 10 14 2 10 12 8 12 3 -12 -...
Otros modelos de este manual:Piscinas - Two Speed Pool and SPA Pump Hydropump (897.55 kb)