Desde dentro del gabinete la posicion del filtro en el cuadro de ronda situado en la parte superior trasera de la caja Se encargara de las estanterias para adaptarse a su conveniencia (ver seccion 6) Espere 48 horas antes cambiar el gabinete en para permitir los liquidos para asentarse Si usted necesita mover El Gabinete de Vino, no vuelca 45 grados, y solo punta hacia la espalda de la unidad. Cercioresele puede conseguir acceso al tapon de la unidad para atender a o mover cuando sea necesario 5

Conexion a fuente de alimentacion El cable de alimentacion del gabinete de vino esta equipado con un enchufe que encaja en cualquier enchufe estandar con conexion a tierra, para evitar cualquier riesgo de choque. Tenga la salida del poder verificada por un electricista calificado para para asegurarse de que es realmente a electricas a tierra. Si este no es el caso, debe tener lo sustituye con un conector que esta debidamente fundamentada Si el cordon esta danado, debe ser reemplazado por un Elec

La refrigeracion de Tecnologia Usted puede registrar tambien su compra de Amcor en linea, y ver nuestra amplia seleccion de productos innovadores. Tabla de contenido Tabla de contenido Gracias ………………………………………………………… 2 Instrucciones de Seguridad ……………………………………… 3 Su Gabinete de Vino …………………………………………… 4 Instalacion …………………………………………………… 5-6 Instalar en el Gabinete o con Puerta Decorativa ……………… 6 Escenarios de Temperatura …………………………………… 7-8 Disposicion & Almacenamiento ……………………………… 9-12 Cuidado y M

75" PVC (NPT) or 1" ID flexible tubing GRAPHIC SIZE...............Overall: 11. 4"H x 16 . 6"W Viewable: 10.608"H x 16 . 3"W STANDARD FEATURES.........Beverage key switch, timed ice agitation and 4" legs ELECTRICAL REQUIREMENTS ..115 V / 60 Hz / 3 Amps SHIPPING WEIGHT............ 240 lb (108.86 kg) c®u* (hsf) C f AGENCY LISTINGS........ .... LISTED City of Los Angeles IN THE U.S.A. Ph: 800.238.3600 Fax: 800.258.0255 OUTSIDE THE U.S.A. Ph: 763.488.8200 Email: webmaster@cornelius.com

These instructions are not intended to cover all details or variations of the equipment, nor to provide for every possible contingency in the installation, operation or maintenance of this equipment. This manual assumes that the per-son(s) working on the equipment have been trained and are skilled in working with electrical, plumbing, pneumatic, and mechanical equipment. It is assumed that appropriate safety precautions are taken and that all local safety and construction requirements are being

The rectangular plate is for use with the six or eight valve Units. 8. Apply RTV (item 5) at the gasket-cabinet joint to seal any gaps between the Units, on all sides of the gasket. 9. Using one screw on each cabinet at the center of the Units (above the drip trays), install drip tray cover to match color of the drip tray. The drip trays must be at the same height along the edges for cover to fit properly. 10. Assemble two long #8-32 screws (item 9) to lower panel (item 1) using plastic washe

Parts List Item No. Part No. Name Qty. 1 629080214 Insulated Lower Panel, Dual 1 2 29677 Rear Mounting Plate 1 3 620023904 Front Mounting Plate (For 6 and 8 Beverage Valve Units) 1 4 32990 Wire Connectors 4 5 50904 RTV Sealant, 3-oz Tube 2 6 620013301 Drip Tray Cover, Black 1 7 620500201 Gasket 150-In 8 620914101 Installation Instructions 1 9 70555 Screw, No. 8-32 By 1 5/16-In. long 2 10 71010 Captivating Plastic Washer, No. 8 2 11 91486 Cornelius Logo 1 ^ WARNING: Disconnect power

Strip red/black wires and reconnect to the key switch using wire connectors (item 4) provided. G. Install beverage panel access covers. 3. Install Adaptor Kits if applicable for the type of ice makers used. 4. Apply self-adhesive gasket material (item 7) to the side of one Unit as indicated in Figure 1. Ends of the gasket should fit tight to each other. 5. Place Units into position on the counter. The Units must be at the same height and sitting level. The outside-outside dimension of the Un

- 1 -Publication Number: 620204725INS ED/DF300 22” CCM322/522 Nordic Style Lid Kit Installation Instructions 4. Seal the icemaker to the top of the dispenser after determining the correct location for the ice maker (see Figure 1). A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so that the ice maker will set on the RTV. B. Set the ice maker onto the lid and position it as required. C. Wipe away the excess RTV. 5. 5. Drill 0.147” diameter hol

WWW.IceCubes.NET WWW.CorneliusParts.COM (866) 423-6253 (623) 869-8881 IMI CORNELIUS INC One Cornelius Place TD 218 Anoka, MN 55303-6234 Telephone (800) 238-3600 Facsimile (612) 422-3246 ED200 & ED250 MODELS ED200 ED250 ED300 Ice Storage 200 lbs. 250 lbs. 300 lbs. Max # of Valves 10 10 12 Built-In Cold Plate BC Model Only BC Model Only BC Model Only Voltage 120 120 120 Phase 1 1 1 Hertz 60 60 60 Amp Draw 3.5 3.5 5.2 Dimension A 30. 30. 44-1/4. Dimension B 30. 30. 30. Dimension C 35-5/8. 39-5/8. 3