Metodo de conexion a tierra recomendado Se requiere una fuente de energia electrica de 115 Voltios, 60 Hz., CA solamente y con fusibles de 15 o 20 amperios, debidamente conectados a tierra. Se recomienda que use un circuito separado solo para su bodega. Use un tomacorriente que no se pueda apagar con un interruptor. No use un cable electrico de extension. NOTA: Antes de realizar cualquier tipo de instalacion, limpieza o de quitar un foco de luz, desenchufe la bodega o desconecte la fuente de ene

OUTSIDE U.S. AND CANADA: This warranty does not apply to, and Turbo Air is not responsible for, any warranty claims made on products sold or used outside the United State and Canada. CHANGES MADE TO WARRANTY COMMENCED ON 5/1/2002 12 Turbo air 1250 Victoria street CARSON, CA 90746 TEL: 310-900-1000 FAX: 310-900-1077 Toll Free: 1-800-627-0032 (U.S.A. In Canada) 13 Turbo air

NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE: THERE ARE NO OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, EXCEPT THE ONE (1) YEAR PARTS & LABOR WARRANTY AND THE ADDITIONAL FOUR (4) YEAR COMPRESSOR WARRANTY AS DESCRIBED ABOVE. THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTY AND MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. OUTSIDE

7 CLEANING ....................................................................................................... 8 BASIC OPERATION ........................................................................................ 9 BEFORE REQUESTING SERVICE ............................................................... 10 WARRANTY..............................................................................................11~12 SERIAL NUMBER The serial number is located on the rating label which is on

IMPROPER USAGE. TURBO AIR ASSUMES NO LIABILITY FOR PARTS OR LABOR COVERAGE FOR COMPONENT FAILURE OR OTHER DAMAGES RESULTING FROM IMPROPER USAGE OR INSTALLATION OR FAILURE TO CLEAN AND / OR MAINTAIN PRODUCT AS SET FORTH IN THE WARRANTY PACKET PROVIDED WITH THE UNIT. ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR INSTALLATION, FIRE, FLOOD, ACTS OF GOD. Turbo Air is not responsible for the repair or replacement of any parts that Turbo Air determines have been subjected after

Condenser fins should be cleaned at least every three months (90 days) or as needed. -To clean condenser, unplug the unit. Condenser can be cleaned with vacuum, brush, or CO2 (high pressure air). 3. CLEAN THE GASKET -The door gasket should be cleaned frequently to maintain proper sealing. 4. CLEAN THE DRAIN PAN -Empty the Drain Pan which is located under the unit, periodically. -When reinstalling Drain Pan, make sure Drain Hose is placed back in pan. 5. CHECK AFTER CLEANING -Plug unit back in. -

2 SERIAL NUMBER ............................................................................................ 2 INSTALLATION OF THE CASTERS.................................................................3 Draft Arms Towers Installation Schematic Diagram......................................... 3 Beer Line & CO2 Line Installation Schematic Diagram..................................... 4 Caution "IMPORTANT" .................................................................................... 5 INSTA

A 620 copper drier or better is highly recommended. 3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained. 4. When compressor is grounded, suction filter drier and 620 drier or better must be replaced. 5. Compressor must be obtained through Turbo Air Inc., unless otherwise specified in writing, through Turbo Air’s warranty department. 11 Turbo air What Is Not Covered By This Warranty Turbo Air’s sole obligation under this warr

The thermostat controls compressor’s cycling by sensing inside temperature. 5. When unit will not be used for a long time, unplug the unit. 9 Turbo air BEFORE REQUESTING SERVICE SYMPTOMS CAUSES SOLUTIONS Cooler is freezing products • Thermostat set too cold. • Turn the temperature dial to a warmer setting. The unit does not refrigerate at all. • There is a power connection failure problem. • Check the power cord to make sure the unit is pluged in it correctly. The unit does not refrigerate well.

3 Beer Line & CO2 Line Installation Schematic Diagram..................................... 4 Caution "IMPORTANT" .................................................................................... 5 INSTALLATION................................................................................................ 7 CLEANING ....................................................................................................... 8 BASIC OPERATION ..........................................................