Depress the ALARM button and stir the shortening freely while it is heating. IMPORTANT! Before the first cooking operation each day, stir the shortening freely while it is heating to provide a balanced shortening temperature for excellent results with the first cooking. Failure to do this can result in a crusty skin on the product surface with an undercooked product internally. In addition, in some cases, failure to stir the shortening while it is initially heating may cause the HI-LIMIT safety

Factory, Simpsonville, SC or F.O.B. authorized BKI Distributor. The user shall have the responsibility and expense of removing and returning the defective part to the Company as well as the cost of reinstalling the replacement or repaired part. Automatic Lift Fryer Table of Contents Table of Contents Table of Contents........................................................................................................................................1 Introduction ..............................

PROGRAM VALVE1 X X refers to the solenoid valve option selected. OPEN is used for Models ALF and BLF Automatic Lift fryers. If your program requires the solenoid valve to be closed while cooking, choose the CLOSED option. 13 Repeat steps 5-12 when programming stages 2, 3, 4 and 5 for Electric and Gas appliance types. Repeat steps 5-10 when programming stages 2, 3, 4 and 5 for an ALF appliance type. The time and temperature of each stage has to be less than the preceding stage. 14 Press ENTER. PR

Use of oil/shortening older than the manufacturers recommendations for life of the oil is prone to surge boiling and flash fires. Follow the oil manufacturers guidelines for the life cycle of oil/shortening. Do not open the drain valve or the fill valve while the fryer is under pressure. Serious burns may result. Follow operator instructions regarding effects of surge boiling of over-wet foods and proper load size. This unit may incorporate components that contain Mercury. The use of Mercury rel

This unit, when installed by an authorized BKI service agent, must be wired for use in accordance with all applicable local, state, and federal codes. For specific electrical requirements and connections refer to the wiring diagram attached to the unit or provided in the Service Manual. 8 Doughnut Fryer Installation Initial Test and Adjustment 1. Fill vat with shortening to about one inch below the mark. NOTE: A solid type vegetable shortening is recommended for frying because doughnuts tend to

13 Doughnut Fryer Operation Cooking Yeast Doughnuts 1. Ensure that the Start-Up procedures have been performed. NOTE: Use fry screens for proofing yeast raised products. Keep the fry screens clean and oily to prevent the doughnuts from sticking to the screens. Hot shortening may splash out of the vat causing severe injury when lowering fry screen into vat. Carefully lower fry screen into vat to prevent shortening splashes. Failure to use the insulated mitts will result in severe injury. Always u

The controller will limit the alarm time to be less than the currently programmed interval cycle time. The default alarm time is 0:00 which disables it. The ALARM time is saved on power down in the same manner as the last interval time. When a time cycle is running and the alarm time has elapsed the internal alarm will sound for 10 seconds. For example, a cycle time 10:00 and alarm time of 2:00 would cause the alarm to sound for 10 seconds once the controller has counted down from 10:00 to 8:00.

Dead Weight Assembly Table 3. Dead Weight Assembly Parts ITEM # PART # QTY DESCRIPTION 1 FT0395 1 PIPE, POPOFF VALVE BAFF BOX 2 FT0396 1 PIPE, DEAD WT TO BAFFLE BOX 3 O0001 1 ORIFICE, SS 4 O0002 1 GASKET, O-RING #2-222 5 PV0001 1 VALVE, POP SAFETY 1321148 6 FT0066 1 ELL, REDUCER 3/4 X 1/2 90 DEG 7 FT0235 1 NIPPLE, 1/2 X C SS 8 FT0190 1 ELL, STREET 1/4 90 DEG CP 9 FT0084 1 COUPLING, BRASS 1/4 10 FT0563 1 FITTING, COMPRESSION .” 11 FT0067 1 BUSHING, C110JO 3/4 X 1/2 CP 12 FT0234 1 NIPPLE, 1/4 X 1

7. Tighten the spin handle until the lid is firmly sealed. Then line up the orange knob on the spin handle with the orange knob at the front of the fryer. 8. Activate the timer by pressing the START/STOP button on the digital timer. The timer will begin the count down. 9. At the end of the frying cycle, the digital timer beeper will sound and the fryer will automatically release pressure into the baffle box. Press the START/STOP button. 10. When the pointer on the pressure gauge is at zero, wait

Burner Tray Assembly 38 Gas Pressure Fryer Replacement Parts Table 6. Burner Tray Assembly Parts ITEM # PART # QTY DESCRIPTION SB3467 1 LP GAS BURNER TRAY ASSEMBLY 1 C0724 1 GAS CONTROL PILOT BURNER O0011 1 ORIFICE, ASSY BBR12 (LGF) 2 C0727 1 GAS CONTROL, STEP OPEN LP 3 FT0399 3 ELL, STREET 1/2" 90 BRASS 4 GB0004 2 BURNER, GAS BRAY LGF 5 I0015 0.083 INSULATION, BOARD 7/16 6 LGFA233 1 BURNER TRAY FRONT W/SLOT 7 LGFA323 1 PILOT BRKT, HOT SURFACE IGNITION 8 ML0064 1 S/S TUBING 304 1/4 DIA CORRUG.18