NO. 1690990 Figure 1. A. Elbow B. Lockwasher, 1/4" C. Screw, 1/4-20 x 3 D. Hose, 6" ID E. Clamp F. Nut, 1/4" G. Clamp H. Clamp I. Capscrew, 3/8-16 x 2" J. Capscrew, 3/8-16 x 2-1/2" K. Hitch Extension L. Lockwasher, 3/8" M. Nut, 3/8" N. Housing O. Hose, 7" ID P. Nut, 1/4" Q. Lockwasher, 1 /4" R. Capscrew, 1/4-20 x 3/4 S. Tube Support T. Lockwasher, 1 /4" U. Nut, 1/4" V. Tube Support W. Capscrew, 1/4-20 x 3/4" X. Hitch A WARNING Do not operate the vacuum collector with any part

Place two 5/16 x 1-1/2 long hex bolts with 5 /16 flat washers through the outside of the cart’s box and through the stake. b. Secure with two locknuts on the inside of the box. c. Install the two door hooks when bolting the rear stakes. Each door hook is bolted to the outside of the cart through the top stake bolt. The end of the hook is facing outward and toward the end of the cart. (DO NOT place the plastic caps over the top of the stakes at this time.) 4. Bolt swivel wheel to the H-frame.

1700259. Located on Blower. I A warning! sn DO NOT OPEN COVER WITH ENGINE RUNNING. DO NOT OPERATE ENGINE WITHOUT COMPLETE CATCHER IN PLACE. Part No. 1676923. Located on Cart (Installed During Setup). A WARNING DO NOT USE THIS HOLE FOR DRAWBAR. TRACTOR TIP OVER MAY OCCUR. Part No. 1700346. Located on Bracket (Installed During Setup). OPERATORS MANUAL MOWER DRIVEN VACUUM COLLECTOR BLOWER ASSEMBLY MFG. NO. 1691260 CART COLLECTOR MFG. NO. 1691187 MFG. NO. 1691320 file 1'^' FORM - 1679

Contents of Turbo Installation Kit 4 Initial Turbo Installation TURBO INSTALLATION Remove Mower Deck Remove the mower deck from the unit (see Operator’s Manual for instructions). Deflector Removal 1. Remove and retain the carriage bolts, washers, lock- washers, and nuts (A, Figure 3) holding the deflector rod to the deck. Remove and discard the deflector rod. Retain the deflector. Install Discharge Baffle 1. Attach the baffle bracket (A, Figure 4) under the mower housing as shown, and insert the

Zeeb Road • Dexter, MI 48130 (734) 996-9116 • FAX (734) 996-9014 1-800-456-7100 251-3845, 7/04 51-3845, 7/04 Table of Contents Section 1 ... Operation and Maintenance Section 2 ... Service Section 3 ... Parts Section 4 ... Appendix 51-3845, 7/04 51-3845, 7/04 Operation and Maintenance M26 Series Table of Contents Introduction .............................................................. 7 Safety .................................................................... 6-12 General Safety Information

No. Description 1694498 Clean Sweep Twin Catcher Rev. 02 Rev. Date 03/2004 TP 100-4033-02-AT-SN Table of Contents Safety Rules & Information General Warnings............................................2 Safety Decals ..................................................2 Storing the Grass Catcher...............................3 General Operating Information Before Operation .............................................3 Mowing with the Catcher .................................3 Required Accessories

6. DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the containers on the ground away from the vehicle before filling. 7. Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground. If this is not possible, then refuel equipment using a portable container, rather than a gasoline dispenser nozzle. 8. DO NOT start gas powered equipment in enclosed vehicles or trailers. 9. Keep the nozzle in contact with the rim o

General Sweeping Minimize dust by reducing brush speeds and by sweeping on days with high moisture. Try to keep wind at your side or back. (Refer to figure 1.) For light material, angle the sweeper 30° left or right. Prevent damage to the sweeper by removing large foreign objects. Preferred Wind Directions When Sweeping Figure 1 51-3845, 7/04 OPERATION SECTION OPERATING TIPS If Material Piles in Front of Sweeper • Decrease travel speed • Increase the engine rpm • Make more than 1 pass • Raise th

1. Adjust height of vacuum inlet. For maximum debris pickup, inlet should be as close to debris as possible without blocking airflow and engine speed set to “FAST”. 2. Inspect debris bag. It must be properly attached to machine, in good condition, clean and dry with the top zipper fully closed. Make sure that the accessory plug is installed into front hole in vacuum nozzle. 3. Start engine. Not all debris pickup will require that the engine speed be set to “FAST”. You can experiment with vacuum