Your heating/cooling unit has been designed and developed to provide safe, reliable, and economic operation when properly installed and maintained. Your year-round air conditioner is a major investment; therefore, you will expect it to perform at its best. By reading this manual, you can learn how to operate it, do recommended routine maintenance, and what to do if a problem should arise. Your new unit should perform at the efficiency level built into it if you will contribute a little of your

7267627267627275TC183.66166.86151.43194.90177.83162.05201.97SHC79.39100.52121.9191.70119.42147.05102.94kW9.829.639.469.589.769.9610.0485TC172.71156.78142.09183.32167.13152.17189.98SHC69.0390.92112.9580.69109.17137.5191.49kW10.8210.6310.4510.5710.7610.9611.0495TC161.37146.24132.38171.36156.04141.86177.62SHC58.4481.04103.7769.4298.67127.7179.83kW11.9211.7311.5611.6811.8612.0512.14 105TC149.57135.32122.21158.89144.45131.10164.74SHC47.5770.9294.3257.8587.91117.6167.79kW13.1212.9412.7712.8913.0613.24

Bhp — Brake Horsepower NOTE: Maximum continuous bhp for the standard motor is 6.13. The Watts — Input Watts to Motor maximum continuous watts is 5180. Do not adjust motor rpm such that motor maximum bhp and/or watts is exceeded at the maximum operat *Standard low-medium static drive range is 873 to 1021 rpm. Alternate ing cfm. See Table 24 for more information. high-static drive range is 1025 to 1200. Other rpms require a field- supplied drive. —27— Table 14 — Fan Performance — 580F180360 (High

Instructions continued on page 8. —3— NOTES: 1. Dimensions in ( ) are in millimeters. 2. Refer to Fig. 4 and 5 for unit operating weights. 3. Remove boards at ends of unit and runners prior to rigging. 4. Rig by inserting hooks into unit base rails as shown. Use corner post from packaging to protect coil from damage. Use bumper boards for spreader bars on all units. 5. Weights do not include optional EconoMi$erIV. Add 90 lb (41 kg) for EconoMi$erIV weight. 6. Weights given are for aluminum evapo

FEATURES/BENEFITS • Efficient rooftop line for cooling using scroll compressor technology • Efficient rooftop line for heating using dimpled heat exchangers • High reliability — non-corrosive condensate pans, prepainted cabinets and primed interior panels, and all units are fully protected by internal safeties • Quiet operation — isolated compressor plate. All compressors mounted on independent vibration isolators. Standard, belt-driven evaporator fan motors on all units • Ease of maintenance ac

Ib mount the disconnect on this panel, align one of the disconnect box knockouts with the unit high-voltage inlet hole and secure the box to the panel. Route the wiring from the disconnect through the aligned knockout and unit inlet. WARNING: Ensure that the drill does not damage any components when drilling through ihe panel. 2. Run high-voltage leads to unit control box and connect leads to contactor. See unit wiring label and Figure 11. NOTE: On 3-phase units, the third power lead is conne

For propane operation, conversion kit P/N 301625-703 must be field-installed. Model 585B units have two A.G.A.-certified heating input ratings. See Table I. These units are designed for outdoor installation either on a rooftop or at ground level on a slab. The cooling section is factory-charged and sealed, minimizing installation time. Installation is easy—connect gas supply, air ducts, condensate drain, high- and low-voltage wiring, and install the air filter. NOTE: An optional condenser coi

The pilot flame then ignites the burners. The 821 heating blower relay (2G) was energized when the circuit through the thermostat was completed. After a short delay, the blower relay (2G) contacts close and the circuit to the blower motor (3D) is completed. This circuit energizes the motor to start the blower. When the thermostat is satisfied, the circuit between R and W within the thermostat will break. On units equipped with the glow-coil pilot, the circuit to gas valve (5A) is deenergized a

The 585A/YACR is the natural or propane model supplied with the RELITE-type pilot that saves gas by operating only when the wall thermostat calls for heating. The 586A/YACX is the deluxe model with RELITE-type pilot and many value added features for reliability and performance. These units are designed for outdoor installation either on a rooftop or at ground level on a slab. The cooling section is factory-charged and sealed, minimizing installation time. Installation is easy—connect gas supply

1). 2. Be sure the installation conforms to all applicable local and national codes. 3. These instructions contain important information for the proper maintenance and repair of this equipment. Retain these instructions for future use. CONTENTS Page SAFETY CONSIDERATIONS ...................... 1,2 INSTALLATION.................................2-14 I. Locate the Unit............................ 2 II. Unit Duct Connections...................... 9 III. Rig and Place Unit ...................